Question about 2007 Audi A3

1 Answer

Headlight range my dashbord shows an orange light with an exclamation mark reading "headlight range defective" kindly assist to fix the problem

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Audi Master
  • 733 Answers

IF U HAVE XENON HEADLIGHT WITH AFS{WHEN U TURN THE WHEEL THE LIGHTS TURN ALONG} THEN THE MOST POSSIBLE PROBLEM U HAVE IS A FAULTY HEADLIGHT.NEED FAULT CODE THOUGH AND VIN TO HELP U FURTHER!!

Posted on Mar 26, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: HEADLIGHT RANGE CONTROL WARNING LIGHT

Hi
I have a 2007 audi A6 2.7 TDI. The headlight range controller warning light stay on, how can I solve my problem?

Posted on Mar 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is an audi a4 everytime i start the engine the symbol for dynamic headlights range control shows up, how can i reset it?


You need to repair the fault....usually caused by a defective suspension height sensor or headlight adjustment motor.

Feb 19, 2015 | 2004 Audi A4

1 Answer

I have this orange light show up on a 2011 Volkswagen jetta it's orange parenthesis with and exclamation in the middle


I suspect that it may be an engine or tranny fault report light As it is coloured I suggest you have the fault codes read befor the fault becomes critical Check in the owners manual for what it means

Mar 10, 2013 | Cars & Trucks

1 Answer

How do you remove the headlight assembly on 1995 ford f250?



  • 1.
    Remove the two upper screws from the headlight housing, using a Phillips screwdriver.
  • .
    Locate the two lower retaining nuts inside the engine compartment at the bottom of the headlight housing. Remove the nuts using a ratchet, extension and socket.
  • Separate the turn signal and marker light assembly from the front grill. Rotate the bulb holders counterclockwise and pull them out of the assembly. Set the assembly aside.
  • Unplug the headlight bulb connector from the bulb. Rotate the retaining ring counterclockwise one-eighth turn and remove it from the housing. Pull the headlight bulb straight back and out of the housing. Do not rotate the bulb during disassembly.
  • Lift up on the headlight housing retaining clips to unsnap them from the headlight housing vertical adjuster studs.
  • Locate the horizontal adjuster at the outer bottom corner of the headlight assembly inside the engine compartment. Loosen the horizontal adjuster until it is free of the adjuster nut.
  • Remove the headlight housing from the vehicle.
Installation
  • Install the headlight housing in the front grill.
  • Engage the horizontal adjuster screw with the adjuster nut and screw it partially in.
  • Snap the headlight housing clips on the vertical headlight adjuster studs.
  • Insert the headlight bulb into the headlight housing, flat side up. Slightly rotate the headlight bulb to engage the grooves in the light with the alignment tabs in the back of the housing. Install the retaining ring on the bulb. Plug in the headlight bulb connector.
  • Install the bulb holders in the turn signal and marker light assembly. Install the assembly in the grill. Install the two upper screws, using a Phillips screwdriver. Install the two lower retaining nuts, using a ratchet, extension and socket.
Headlight Aiming
  • Pull the vehicle to within a few inches of a blank wall, on a flat surface. Apply two strips of tape to the wall vertically to mark the centers of the headlights. Apply a strip of tape to the wall horizontally to mark the center of the headlight height. Back the vehicle up 25 feet in a straight line.
  • Turn the headlight low beams to the "On" position.
  • Adjust the vertical headlight adjusters until the high-intensity zone of the light pattern is two inches below the horizontal mark on the wall.
  • Adjust the horizontal headlight adjusters until the high-intensity zone of the light pattern is two inches to the right of the vertical headlight marks on the wall.

Nov 08, 2012 | Cars & Trucks

1 Answer

I have a 2000 buick regal none of my dashbord lights work and the lights for the radio and heat,fuses are all good


The first thing you want to check is the panel light dimmer control on the headlight switch. Make sure it isn't turned way down.

Apr 10, 2011 | 2000 Buick Regal

1 Answer

My dashbord light dot work and my tail light dot want to come on but evertyng else work please get back to me thank you.


No dash lights and no tail lights means it's time for a new headlight switch. Hope this helps.

Aug 16, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

Passenger Headlight keeps going out. While


sounds like the head light switch may be defective.

Aug 14, 2009 | 1987 Nissan Pickup

1 Answer

Who can answer this


From what I have seen, it looks to be a blown bulb indicator. Check all of your lights to make sure that they are in proper working order including turn signals, park lights, headlights, and tail lights.

Jun 23, 2009 | 2005 Jeep Liberty

1 Answer

Head / fog light adjustment


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jul 02, 2008 | 1994 Toyota Supra

Not finding what you are looking for?
2007 Audi A3 Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...