Question about 1999 Chevrolet Malibu

1 Answer

Where is the MAP/VAN on 99 malibu - 1999 Chevrolet Malibu

Posted by on

  • 426 hemi May 11, 2010

    Need to be more specific. Do you have a four cyl or six cyl eng? The map sensor on 4 cyl 2.4 ltr is on the right front of the throttle body. right in front of the throttle position sensor. on a V6 engine the map sensor is located on the upper intake manifold plenum.. dont know what van is, good luck..



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,640 Answers

If 3.1 it is on top in back before coil pack! it is a oblong type of sensor, has wire connections to it and a vacuum hose.

Posted on Jun 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 malibu popping sound

didnt specify much but bad damaged valves --skipped timing chain -clogged cat converter can cause overheated manifold [s ] but are not only reason need to do compression test , timing and exhaust pressure

May 01, 2017 | Cars & Trucks

1 Answer

When a map sensor starts going out will it cause a 99 chevy Malibu 3100v6 to quit while driving?

The MAP sensor should only throw a check engine light. Either a bad ignition control module or a fuel pump are going to cause the issue your stating. Start with those, dont be afraid of forums as well, very good DIY's to be found. The 3100 V6 is a 3100 v6 no matter if its in an impala or a malibu or even oldsmobiles and buicks. Good luck.

Jan 07, 2015 | Cars & Trucks

1 Answer

99 Malibu cuts out kinda like it starving 4 fuel, changed plugs,fuel filter, could it b the map sensor?

There are many things that will cause this problem, could be a fuel pump or pump relay, mass air flow sensor etc,

The best thing to do first would be to go to an auto parts store that does scanning. have the computer scanned and see if there are any stored codes, if so get the codes and let me know what they are.

Dec 08, 2012 | Cars & Trucks

1 Answer

I have 99 Chevy Malibu. My check engine light came on. The original codes were for a cylinder misfire and a small emissions leak. I replaced the injector for the cylinder that was misfiring as well as all...

well if you get it scanned again, and you get a lean bank 1 and 2 code then you may have a intake manifold gasket thats leaking. I just worked on a van that had them codes. and I ended up changing the intake manifold gaskets to get it to pass the emissions test for inspection, I live in new york state, po171 and p0174 are the lean codes. we did the maf sensor, new 02 sensors, egr valve and still got this lean code. good-day and god blessyou. it was on a 99 ford windstar van.

Oct 03, 2011 | 1999 Chevrolet Malibu

1 Answer

99 chevy malibu no dtc code p1665

where can I find the P1665 Evap vent solenoid control circuit on my 99 Malibu?

May 20, 2011 | 1999 Chevrolet Malibu

1 Answer

The interior lights of my 99 chevy malibu do not work. Can this be a fuse problem?

yes it can be a fuse, most cars have a dimmer for dash/interior lights if fuse is ok it may be the dimmer switch.

May 20, 2010 | 1998 Chevrolet Malibu

1 Answer

I need the engine torque specs for 99 chevy malibu. like the head bolt torque sequence and rocker bolt torque sequence

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Mar 12, 2010 | 1999 Chevrolet Malibu

2 Answers

99 malibu

check idle, for a 3.1 it should be about, 750 rpms,

Oct 06, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides