Question about 1998 Acura TL
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.
btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.
Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.
If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.
If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)
Posted on Jan 05, 2009
just did it tke a breath and put on your small hands!If you r talking about hid bulbs i found aftermarket bulbs at www.moble-emotions.com its best to get both and change them togetherso they match i did only one first and you could see the differance big time.On the battery side the black cover to lightbulb neens to b poped off there r two thumb push tab pry light with a screw driver. on pass side take the 10mm bolt off washerbottle and move aside.(.you need a small hex or starbit to remove the set screw.after u get the set screw off takr both hans and twist hard the cover has a slot as u turn off pull out.there is a hook tab about the size of a paperclip un hook at bottom bulb its fixed at top so just lift bottom to top.remove and replace bulb.(twist out )reverse stepsI also looked at a picture on acurra parts site goood luck i think i did it better than discribing
Posted on Nov 11, 2009
Testimonial: "thanks, your direction was very helpful..."
There are two mechanical noises you will hear from an engine, lifter noise, wrist pin slap, and rod bearing noise. The only one that will go away, if at all, with engine warm-up, is lifter noise. All assuming of course, the noise is coming from the engine, and not any of the externally mounted accessories.
Have the oil changed, and continue to change every 2000-3000 miles with a good quality oil, maybe the lifter will clear itself. If it does, maintain the oil changes for the next few changes to assure it is cleaning out.
You might also try adding 1-2 pints Berrymen's Chemtool to the oil 200-300 miles before you plan to change the oil.
Posted on Dec 13, 2009
Testimonial: "THE ACURA TL 2007 USE HIDRAULIC LIFTERS? WHERE?"
Tips for a great answer:
Feb 02, 2014 | 2005 Chrysler Sebring Conv
Apr 16, 2013 | Acura TL Cars & Trucks
Jul 21, 2011 | 1996 Acura TL Series
Jan 31, 2011 | 1996 Acura TL Series
Jul 30, 2010 | 1996 Acura TL Series
Jun 25, 2010 | 1996 Acura TL Series
Jun 10, 2010 | 2000 Acura TL
Dec 02, 2008 | 1998 Acura TL
59 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: