Question about 2009 Hummer H3

1 Answer

Blower resistor pigtail connector

Wires burned out on pigtail connector for blower

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

GM with Hummer has a recall pending on that exact thing due to possibility of a fire. Contact your dealership to see when they finalize the recall, right now they are still working on a part for the fix before they begin having anyone bring their H3 in to be fixed.

Posted on Jan 21, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace pigtail connector on blower motor for a 1998 chevy malibu


You have to cut the wires and solder, or use butt-connectors, to hook up the new one. I also recommend replacing the blower motor resistor. Having enough current to damage the connector has put a lot of strain on it also. It is also in the same area as the blower motor.

Jan 28, 2013 | 1998 Chevrolet Malibu

1 Answer

I had my blower checked in my 2002 bonneville they said it was fine but there was a pigtail wire that connects to the back of it that was burned up,what is this wire and can it be replaced quick and cheap.


That's your resistor that's burned up under the connector. Get a new one and ask if they have the pigtail to go with it. You must have had an untrained mechanic.

Apr 15, 2011 | 2002 Pontiac Bonneville

2 Answers

1996 astro chevy van heater use to work on low and med but wont work at all now.


The blower resistor has gone bad which is why you lost blower speeds.This may have been caused by the blower motor drawing too much power. At this point I would verify that no fuses burned out and then check the pigtail plugs going to the resistor and blower motor to make sure the connectors and connections are not melted or wiring is frayed. These connectors are located in the engine compartment on the passenger side. After checking this and if everything appears ok then the blower motor itself has probably gone bad and needs replaced. I would also replace the blower motor resistor as well. If the connectors appear damaged replace or repair as needed .

Jan 10, 2011 | 1995 Chevrolet Astro

1 Answer

My heater stopped working, one day a smell & some smoke came out of the vent... I bought a new resistor & its not fixing it> whats next?


Check the pigtail to the resistor and the pigtail connector to the blower motor.Look for burnt wires or melted connection. The blower motor itself may be bad. You can try wiggling the connectors to see if it comes on or tapping on the blower motor.If it comes on doing either the connection is most likely very poor and needs repaired. You can also check fuses just to make sure when whatever burned out it did not blow the fuse.

Sep 29, 2010 | 2004 Pontiac Grand Prix

1 Answer

How do I change a blower motor in a chrysler Town and country


Hello, to change the blower motor resistor follow this steps:
  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Aug 25, 2010 | 2006 Chrysler Town & Country

1 Answer

I have 06 trailblazer, on the a/c i replaced the air blower resistor and keeps burning on the blackwire from the resitors pigtail connection. Should I replace the resistor and connection, or is their a...


{: ) Try first to repair the terminal connectors to achieve a tight connection and contact. Check also the integrity of the black wire which is supposed to be the ground wire. Its a better option if you replace also the resistor along with connector.

Aug 08, 2010 | 2006 Chevrolet Trailblazer

1 Answer

Blower not turning to push air and heat through vents, Replaced blower motor, still not working. How do you get to the dash wiring to check electrical connections. fuse is good.


Replace the Blower Resistor. (About $12).

The resistor might be good; I have found that the terminals corrode, create resistance and sometimes melt the connector (About $100). Check the resistor before replacing it! If the connector gets fried, solder pigtails onto the good resistor and use Marr connectors to attach the pigtails to the existing wires,

Jul 12, 2010 | 2001 Dodge Dakota

1 Answer

Heater fan only works on high


The blower resistor needs to be replaced. The blower motor resistor is located in the passenger foot well, it is mounted inside the heater case near the firewall and the blower motor. This is an extremely common problem with these vehicles, and the problem is in the wiring connector that goes to the resistor module. The blower motor draws current through the resistor pack at an excessive rate and causes the wiring terminals at the resistor pack to melt and loose connection. The most effective and permanent fix to this problem is to replace the connector end, the blower motor, AND the blower motor resistor. You can usually get away with just repairing the wiring at the resistor module, however it is extremely likely that the problem will repeat itself in the future. The connector ends are available at your local GM dealership, are relatively inexpensive, and they come in a package that contains the connector pigtail and heat-shrink **** connectors, however to maximize model coverage they manufacture the pigtail so that all of the wires are white. This means that your wire colors will not match up, and you will need to snip and crimp each wire separately as to avoid confusing their positions in the connector and accidentally wiring the resistor pack incorrectly. Inspect the resistor module for melted terminals as well, usually the module needs to be replaced because of melting damage. Should you choose NOT to replace the blower motor, the system will likely work in all speeds after repairing the connector, but you are taking your own risk towards the problem happening again. Good luck

Dec 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Blower motor works intermittenly & I smell burning wires


you need to replace motor itself im sure on this you can find a used one on car-part.com i should have one wreckcars@aol.com

Dec 24, 2008 | 2003 GMC Sierra

Not finding what you are looking for?
2009 Hummer H3 Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...