Question about 1996 Honda Accord
There will be a number of smaller screws around the outside of the bumper, like in the wheel well and under the car by the splash shield under the engine. All of those will need to be removed. Then you need to remove the turn signal lights in the front bumper with a long phillips screwdriver. Take a flashlight and look inside the bumper through the lower grill at the side of the turn signal housing. You'll see a small hole for the screwdriver. The screw doesn't need to come all the way out to remove the light.
Remove turn signal housing on both sides and look back at the frame crossmember behind the bumper. There are two large bolts on each side holding the bumper on. You'll need some extensions to reach them. Once those are out, you'll be able to tell if you missed any smaller screws/clips.
Posted on Jul 01, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
*The Turn signal on the Side of the car next to the headlight*
1. Open the retractable headlights.
2. Remove the plastic shroud around the headlight: two screws in front and one on each side.
3. Look to the outside of the headlight and you will see a single screw in a small plastic cover on the front inside edge of the signal light assembly. The headlight prevents you from getting at the screw straight-on. I broke it loose with an offset phillips screwdriver, and then backed it out with a regular phillips.
4. Remove the plastic cover, and you will see two screws. Remove them.
5. Now you can pull the turn signal assembly forward and out.
6. To remove the bulb holders from the assembly, twist counterclockwise and pull out.
7. Pull straight outward to remove the bulbs. To assemble, follow the steps in reverse. Note that there are two plastic rods on the back end of the turn signal assembly that you will insert into two holes in the channel of the fender
*The turn signal in the bumper*
1. You will need a phillips head And Flat head screw driver, right below the turn signal there is a panel that you can pop out, (or its allready gone, Looks like a Fog light can go in there.)
2. once u find that, (Pretty easy to find) Look directly up in there., there is styrofoam up there and u will also notice a little hole,
3. Stick the Phillips head screw driver in that hole and turn it counter clockwize, The screw will not fall out,
4.once it feels like the screw is loose put the flat head in between the turn signal lense and bumper, the side where you unscrewed it and SLOWLY pry it out,
4. once out, just twist the plug and replace light bulb
to replace just reverse instructions
Posted on Jun 30, 2008
start by removing the console. there should be four screws that hold it in; two on each side; one in the front and one in the rear. you may have to take the gearshift knob of if the car is manual trans.then, remove the ash tray. there are two screws at the front of the ashtray receiver and one at the back.with the ashtray and slide removed, take the bezel off of the radio. there should be two screws behind or above the air outlet vents on top andn two screws in the under the center dividing rail. you may have to pop out the air outlets to get to the screws. there may also be a screw at the bottom of the bezel in the center.with the bezel removed the only thing that holds the radio in at that point is two screws that come up from underneath where the ashtray receiver was. take out those two screws and the radio should pull out from the front. Be sure to disconnect the antenna lead and the connector from the back of the radio before pulling on it too hard or you'll damage one or the other.hope that helps
Posted on Jan 17, 2009
there is a pinch bolt that holds it in, make sure you straighten the steering wheel first and lock it down with something so it cant move, then remove the pinch bolt and the pressure and discharge lines from the rack there are return lines within the rack that go side to side, you dont need to remove those. Make sure the replacement rack is even when putting back into steering yolk
Posted on Sep 02, 2009
Detach the cable from the negative terminal of the battery. Caution: If you have an anti-theft radio, make sure you have the activation code before disconnecting the battery.
Remove the battery and battery tray from the engine compartment (remove the battery first, then remove the bolts for the battery tray and remove it.).
Remove the lower radiator hose and the wiring harness from the starter bracket. Make sure they are positioned out of the way.
Clearly label, then disconnect the wires from the terminals on the starter motor solenoid (the smaller cylinder attached to the starter). Disconnect any clips securing the wiring to the starter.
Remove the mounting bolts (two) and detach the starter (pull it gently out of its housing).
Reverse this procedure for installation.
Hope this is of help to you.
Posted on Dec 26, 2009
Tips for a great answer:
Mar 24, 2014 | 1996 Honda Accord
Aug 02, 2012 | 1996 Honda Accord
Nov 30, 2010 | 1996 Honda Accord
Aug 10, 2009 | 1996 Honda Accord
Jul 17, 2009 | 1991 Honda Accord
Jun 17, 2009 | 1996 Honda Accord
Mar 24, 2009 | 1996 Honda Accord
Mar 17, 2009 | 2004 Honda Accord
Jul 15, 2008 | 1998 Honda Accord
Jun 30, 2008 | 1995 Honda Accord
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: