Question about Ford F-350 Super Duty

1 Answer

Cracked bell housing

93 dump

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,480 Answers

My initial thought is Aluminum can be welded. Depends on cracks relationship to mounting bolts. Check and see if Bell housing is separate from transmission. May be able to swap bell housings and keep transmission.

You may want a good Salvage yard site like Carparts.com. They have a Nationwide link to many Salvagers. One request and you could get 300 responses.

Posted on Mar 29, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there antifreezes leaking out of bell housing on a 1999 dodge Cummings diesel engine, is it a freeze plug or a crack in block


there almost certainly will be a freezeplug in that area , but first make completely sure the coolant isn't leaking higher up and looks like from bell housing , get the area steam cleaned and make sure it's not from the head gasket or another freeze plug , 30 minutes spent doing this could save you time and money dropping the gearbox etc , hope this helps

Nov 05, 2014 | Cars & Trucks

1 Answer

Pathfinder nissan 96


crankshaft seal would be my starting point

Mar 26, 2014 | Honda Passport Cars & Trucks

2 Answers

Replaced starter wneh starting the bell housing cracked from bolt


Assuming you installed the correct starter
& it wasn't you installing it in some old way

You will have to have the bell housing TIG
Welded, if you need the broken piece on there

Jun 12, 2011 | 1993 Honda Accord

1 Answer

I have a 1985 S10 with a 4 cyl engine 4 speed . Can I use a later model 5 speed trans in this truck with the 4 cyl engine?


I believe so. The 4.3 has the same bell housing as 350/305. It is different from 2.8 and 2.5. But from what I remember the 2.8 and 2.5 were the same. I can only speak for years up to 93. I know on the later models the slave cylinder is inside bell housing and the speedometer would be different. Probably too much trouble even if bell housing was the same.

Feb 15, 2011 | 1985 Chevrolet S-10 Blazer

1 Answer

Steps required to remove the standard transmission from a 1992 Toyota pickup. Bell housing bolts, starter, and rear trans. support have been removed, but the trans/bell housing will not separate from from...


Make sure you have removed all the bolts ....you will have to pry hard to remove it out .....be careful not to crack the bell housing ..Pry around the bell housing .good luck

Jan 02, 2010 | 1992 Toyota Pickup

1 Answer

93 or 94 Dakota Transmission


look at the starter bolting the location on bell housing differ depending where manufac...
plus start counting splines on the shafts..

May 07, 2009 | 1994 Dodge Dakota Club Cab

2 Answers

Remove transmission 93 toyota pick up


You'll have to disconnect the cross member that holds everything in. Jack it (the motor) up first or it will fall out faster than you ever imagined.

Feb 13, 2009 | 1993 Toyota Pickup

1 Answer

Car wont start 93 buick century


to find the crank sensor you have to remove the bell housing and then the plastic guard behind the bell housing....fusible links sorry I do not know

Jan 12, 2009 | 1993 Buick Century

1 Answer

Clutch wont depress or go into gear. bell housing cracked


If the bell housing is cracked,then the input shaft is probably bound up, as is your clutch components also.Replace the tranny or bell housing if applicable.Good Luck!!!

Aug 04, 2008 | Chevrolet 3500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...