Question about 2008 Dodge Durango
Won't go up or down
If all the windows do not work, I agree with the blown fuse. If the fuse is OK, check the relay. If that is ok then you may have to replace the drivers side switches. All of the window power goes there first. If you recently removed the door panel, check that the connector for the switches inside the panel is seated properly.
Posted on Apr 13, 2015
Posted on Apr 07, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You need to replace the regulator inside the door. It's the little pulley system that will pull your window up and down when you push the button.
Takes about 20 minutes to fix, so you're looking at about 100.00 at the garage.
Posted on Dec 18, 2008
I know its not what anyone would want to here but sounds like a short. Best thing to do is first wiggle your key switch when the vehicle in in the on position then at the same time try to check to see if locks or windows are working. Then do the same in while the rig is running. If that dont work your ignition is fine and you need to take off door panels and check and wiggle all conections on window motors and lock motors and look for melted or burt wire or some that might have got hot. If all is good there you need to go to the back of the fuse box were the fuses to those items plug in and check there. As far as the service engine light goes either take it to the nearest Schucks or AutoZone and they will check it for free if not cycle the key on and off 3 times and on the 3rd time leave it in the on position look at your odometer light and it will flash a code remember that code and type Dodge then the code on yahoo search and it should tell you why your light is on Hintz whay sensor is bad. Hope this helps.
Posted on Apr 05, 2009
Remove the door panel and find the window motor Unplug it and using a separate car battery run cables directly to the window motor When you switch the polarity the motor will either bring the window up or down or if noting happened change the window motor and window regulator assembly.
Posted on Jun 08, 2009
A Mechanic told me my switch was broken, but the switch was working fine, the lights just stopped flashing. After some research and consulting with a male friend who knows more about this than I, we discovered it was only the turn signal flasher -- a $16.00 part. On the 2000 model, it's located under the dash, on a separate fuse panel I didn't even know was there. It's to the left of the steering column and right behind the main fuse box, but you can only get to it by going up under the dash. The green one is a little hard to get to, but that's the one for the hazard lights. Its easy to see with a good shop light. It's 1" by 1" ish. The turn signal flasher is below the green one. It's black and a little smaller, and much easier to get to. You simply unplug it and plug the new one in. Voila! There are other fuses on this panel -- I'm not sure what they go to, but I intend to find out so I don't waste money replacing parts I don't need to.
Posted on Jan 20, 2010
Tips for a great answer:
Aug 11, 2012 | 1998 Dodge Durango
Sep 14, 2010 | 2004 Dodge Durango
Jun 08, 2010 | 2006 Dodge Durango
Apr 05, 2010 | 2006 Dodge Durango
Mar 12, 2010 | 2001 Dodge Durango
Nov 13, 2009 | 2002 Dodge Durango
Aug 02, 2009 | 1999 Dodge Durango
Jun 11, 2009 | 2001 Dodge Durango
208 people viewed this question
Usually answered in minutes!