Question about 2009 Mazda CX-9 Grand

Open Question

Cx-9 abs contol module

Abs light on

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Buick Lacrosse CX- ABS and T/C dash lights on (not engine light). The continuing saga.


Have the ABS codes checked. Check for power and ground at the wheel sensor harness. Check the ground wire from the ABS module to the body. I always move it from the bracket to the body. Just a note.. You will still have brakes.

Mar 19, 2016 | Buick Cars & Trucks

2 Answers

ABS and T/C lights on dash. Resistance measurement good on left and right wheel speed sensors. Haven't been able to find an ABS and T/C wiring diagram to see what is common to both. circuits.


ABS and traction control both use the wheel speed sensors and are controlled through the same module . What resistance readings did you get ? Did you test AC voltage with the wheel spinning ?

Feb 10, 2016 | 2006 Buick LaCrosse CX

1 Answer

My 2007 nissan pathfinder ABS, 4x4 and traction control lights comes on


These systems are tied together, you may have one of the following problems. Could be a bad ABS senor, one of the modules my be bad, a wiring issue or a problem with the PCM (powertrain contol module). Have it checked by a techician that knows your make of vehicle.

Jul 18, 2014 | 2007 Nissan Pathfinder Off Road

1 Answer

How to adjust headlights


In my CX-9 on the left side of the drivers dash, below the steering wheel, there is a little adjustment wheel for headlight up and down adjustments. I believe it has 3 or 4 positions. Check out the video at 1:13 mins in.
2011 2007 Mazda CX 9 Automatic Xenon Exterior Lights Tutorial

Jun 02, 2014 | 2007 Mazda CX-9

1 Answer

Dual thermostat contol not working on passegner side. blows only hot air.


This fault could be control module related. The Dealer will have the computer to rectify this issue. Have a quick look under the dash on the passenger side, can you see the hot/cold rotor moving as you increase/decrease the heat temp? If it is moving the air direction flap may have become detached.
Hope this helps...

Mar 03, 2011 | 2007 Mazda CX-9

1 Answer

Abs and traction control light came on after washing car


You probably got water in a sensor or plug in connector. Give it time to dry and it should be okay. You may have to erase the trouble code to get the light back off.

Nov 19, 2010 | 2008 Mazda Cx 9

2 Answers

Abs light and brake light stays on, speedometer does not function below 20 mph


The problems you are describing will relate to the vehicle speed sensor. All these things need input from it to function correctly.
As your speed increases the voltage generated increases as well so it may develop enough to operate your speedometer.
I need a little more information to give specific details on where it is on your vehicle.

Nov 04, 2009 | Dodge Ram 1500 Cars & Trucks

3 Answers

What does a service vehicle soon light mean?


the light means there is a problem in he vehicle (not the engine) this could be like a bad bulb, abs unit airbag, gas gauge, tire pressure. scan the body contol module should tell you why the light is on.

Aug 27, 2009 | 1997 GMC Jimmy

1 Answer

2000 Ford Ranger


TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Jun 11, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2009 Mazda CX-9 Grand Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...