Question about 2007 Volkswagen Passat Sedan

1 Answer

Left rear calipier

Supply voltage fault

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 67 Answers

You mean the electric handv
brake?it is the small engine electrical on the caliper,
replace and re initiate by open close with computer,reset controle counter to 0
open and close by computer command,

Posted on Jul 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2008 chevy express, the turn signals flash fast, but not able to find a flasher unit. I have checked grounds, bulbs and fuses, all are good


The BCM - body control module controls turn signals . There is no flasher unit . Your best bet would be to take your vehicle to the dealer !
Turn Signal Lamps
The BCM 3, BCM 5, and BCM 6 fuses located in the underhood fuse block supply battery voltage to the body control module (BCM) for turn signal, hazard lamp, and stop lamp operation. Voltage from the BCM 5 fuse used for the front and rear left turn signals, voltage from the BCM 3 for the right front turn signal, while voltage from the BCM 6 fuse is used for the right rear turn signal. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G303 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.

Ignition ON, observe the scan tool Left Turn Signal Switch parameter while using the turn signal/multifunction switch to turn the left turn signal ON and OFF. The reading should change between Active and Inactive.

Apr 08, 2017 | 2008 Chevrolet Express

1 Answer

07 cadillac cts has no brake light all fuses are good and replace the brake switch.still not working any advice


Stop Lamps
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bass relay close and battery positive voltage is applied through the bass relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

Do you know where the rear fuse box is ? Check BAS fuse 15amp. and the bas relay , should be marked on the inside of the fuse box lid . The rear fuse box is located

Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Right Rear
In the passenger compartment, under the right side of the rear seat at carpet.

If fuse and relay are ok your best would be to take to a cadillac dealer .

Jan 19, 2017 | Cadillac Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

2008 Cadillac SRX Why do right turn signals flash much faster than left? All bulbs are illuminated.


The turn signals on your vehicle are computer controlled by the BCM - body control module . The first place to start would be to hook up a scan tool that can access BCM DTC'S an data Parameters. If all the turn signal bulb's are good .
Turn Signal Lamps
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch circuit. Battery voltage is applied at all times to the BCM. The BCM then applies a pulsating voltage to the front and rear turn signal lamps. Ground for the front turn signal lamps is supplied at G104. The left rear turn signal lamp is supplied ground at G402 and the right rear turn signal lamp is supplied ground at G401.
High resistance some where in the turn signal circuit could also cause this type problem . Doing voltage drop testing on the circuit would find a problem of high resistance .

High Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Oct 19, 2016 | Cadillac Cars & Trucks

1 Answer

I just purchased a 2005 cadilllac srx v8 n i cannot get the third row seat tto function? Help?


Rear Seat Switches
There are three push button switches that are used to operate the power folding seat; front stow switch, rear stow switch, and recline switch. The front stow switch is located in the right rear quarter trim panel just behind the second row seat. The rear stow and recline switches are located in the right rear trim panel just inside the liftgate. Battery positive voltage is supplied at all times to all three switches from the FFS SW Fuse located in the left rear fuse block. The folding seat will operate only in a supervised mode, i.e. press and hold the selected switch button through the entire cycle of operation, or release the switch when the desired seat position is reached. When any folding seat switch is pressed, it sends a 12 volt signal through the switch signal circuit to the RSM. The RSM then commands the appropriate seat motors to move in response to the switch signal.
Rear Seat Module and Power and Ground
The rear seat module controls the position of the third row seat. When commanded it moves the seat from the seated position to the stowed position, or, from the stowed position to the seated position. With the seat in the seated position, the RSM can also move the angle of the seat back forward or rearward.
Battery positive voltage is supplied at all times to the module through the battery positive voltage circuit and the FFSM fuse located in the left rear fuse block. This voltage is used to power up the RSM and also to apply power to the seat motors when commanded. The RSM is grounded through the module ground circuit and G401.
The first place to start would be check the fuse's .Do you know where the left rear fuse block is located ? Fuse Block - Left Rear
In the passenger compartment, near the left side of the rear seat under the carpet
If the fuse is good next thing to do would be ,have check for DTC'S in the rear seat module ! This has nothing to do with check engine light or OBD 2 diagnostic trouble codes an a code reader for said OBD2 codes will not work . Would need a factory scan tool to check these codes.
DTC B1395
Battery positive voltage is supplied at all times to the rear seat load floor switch and the rear seat position switch by the rear seat module (RSM). The RSM monitors these battery positive voltage supply circuits for the protection of internal circuitry of the module.
DTC B1395 Device Voltage Reference Output 1 Circuit
DTC B1420 Device Voltage
Battery positive voltage is supplied at all times to the seat adjuster switch and the memory seat module (MSM) through the same circuit. The MSM uses this battery voltage input to determine if battery positive voltage is applied to the seat adjuster switch.
DTC B1545 Seat Stow Switch 1 Circuit


?€¢
DTC B1546, Seat Stow Switch 2 Circuit


?€¢
DTC B3729 Seat Recline Control Switch


DTC B1735 Seat Front Up Switch Circuit


?€¢
DTC B1740 Seat Front Down Switch Circuit


?€¢
DTC B1745 Seat Rear Up Switch Circuit


?€¢
DTC B1750 Seat Rear Down Switch Circuit


?€¢
DTC B1755 Seat Assembly Horizontal Forward Switch Circuit


?€¢
DTC B1760 Seat Assembly Horizontal Rearward Switch Circuit


?€¢
DTC B1815 Seat Recline Forward Switch Circuit


?€¢
DTC B1820 Seat Recline Rearward Switch Circuit


Just from looking at the factory service info , I'd say you would be bet off just taking this to the dealer !
The first plase

May 28, 2016 | 2005 Cadillac SRX

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Rear piston stuck in calipier


If you are talking about the rear disc brake caliper, then you need to replaced the caliper with a rebuilt unit.

Feb 02, 2009 | 1995 Nissan Maxima

2 Answers

Rear brake pads


You need a spanner tool. You have to rotate the piston clockwise until it screws back into the calipier. DO NOT USE A C CLAMP as this will brake the calipier.

Aug 17, 2008 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
2007 Volkswagen Passat Sedan Logo

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...