Question about Suzuki Cars & Trucks

1 Answer

Fiero clutch jerking

My bike suzuki fiero low picup and clutch jerking

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

As SUZUKI Fiero, bike.
now that is an all time first there, please do add image. below.
must be some rocket that ,

Posted on Mar 24, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 90 Answers

SOURCE: My Suzuki Liana 2007 (1.3L with M13A engine) jerks at low speed.

I cant say I have ever even seen one of these, but lets start with this; Most vehicles can tolerate quite a lot of moisture (driving in heavy rain) but when it is 'flooded' with water, even garden hose pressure, that water is going to get into places it shouldn't. Your mechanic may may be going down the right path but try this first; remove spark plugs and replace if they have 50k or more miles or any are dark brown to black on the porcelain around center electrode. When you gain access to them and after turning them out about 1.5 turns, blow out water and/or dirt from around them with compressed air, this keeps it from entering plug hole. While you are using air, blow out spark plug wires/boots on both ends. As I first said, I am not familiar with this engine at all so I am not sure if you have a single coil or multiple coils. Blow out any water in any connections to these if possible. Replace boots/plug wires if they show any sign of arcing/excess wear (cracks,tears,brittle,torn) or more than 50k miles.When reassembling use a good quality dielectic silicone grease To help 'weatherproof' them.Make sure you did not damage or dislodge any other hoses/tubing/ect.. when cleaning.Hopethis helps! Please rate me. Thanks!

Posted on Jan 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put new starter sensors and coil pack getting fuel and wont fire


Hi jarrod im pierre you got a 4cyl or v6 i remember those fiero the distributor is near the firewall 4cyl the ignition module and picup coli use to get full or corosion everything got green in there the rotor to got a hole in it the v6 you got a check engine when you put the key in on position if not no power to ecm check the fuses on the positive side of the battery the positivecable got a little wire connected to it that you ecm power 6 inch after the therminal that little wire got a coupling pull that litlle wire use to have corrosion in therelet me no more info

Mar 13, 2015 | 1985 Pontiac Fiero

1 Answer

How do u bleed a hadralic clutch on 85 Fiero


this is done the same way as bleeding the brakes. make sure the clutch cylinder does not run out of brake fluid. the pedal should feel firm all the way through its travel and not soft.

Jan 31, 2015 | 1985 Pontiac Fiero

2 Answers

I have a 1986 pontiac fiero 4 cyl. 5 spd . the clutch is moving fine , and so are the cables , but when you let the clutch out , nothing happens , the car does not move .


Does the pedal have "free play" at the top? Perhaps some adjustment is possible. If not, may be time to replace clutch disk.

Jan 14, 2015 | 1986 Pontiac Fiero

1 Answer

I have a 1986 Fiero GT and it is very hard to shift into first, fifth, and reverse. I've checked around online and most say bad clutch, low clutch fluid, or clutch not completely disengaging but that


try to check for gear oil in the transmission itself at rapidlube or valvoline oil change or some thing also spray wd40 on the shift cable as it may have rust inside the cable sheath underneath..have them also check fluid levels in the slave cylinder resorvoir and fill if low.. it costs about the same either way.. but then you will know..good luck..

Dec 26, 2012 | Cars & Trucks

1 Answer

I hv one Suzuki carry picup. That fuel tank out of order for rust. I need new one tank. so I want knw how can i get it


If a new one is out of the question go for a used one in a area that gets hardly any snowfall. No salt is used in those areas

Oct 28, 2010 | Suzuki SX4 Cars & Trucks

1 Answer

My 86 Fiero SE clutch master cylinder is weeping


Replace it. Not a difficult job. Be careful the bracket on the V6 4spd. isn't strong so don't break it while loosening the slave cylinder retaining nuts.

Good luck,

Rebel Faggioli

Dec 30, 2009 | 1986 Pontiac Fiero

1 Answer

My suzuki alto randomly started julting/jerking


i think its fuel problems, check engine oil if it has gas in it...

Dec 28, 2009 | 1989 Suzuki Swift

1 Answer

Car not starting by the key


the actuator is broke in column is what it sound like or switch on column is no good

Aug 11, 2009 | 2006 Suzuki Forenza

2 Answers

1985 fiero been having problems getting in gear. Now wont turn over starter. New starter didnt fix problem. Dont know if 2 problems are related. Can push start.


Have same car, same problems, easy solutions.

Getting into gear has been improved by putting in neutral with engine running to warm up fluid. The Fiero has very little room in the pedal area. I'm shifting a lot better with smaller shoes.

The problem with starting may well be related to the same issue. There is a neutral safety starting switch. If you're not pressing hard enough on the clutch - starter won't run. According to the Fierostore.com stock clutch pedals tend to bend. They sell a stronger replacement.

My Fiero has been starting just fine the last few days. The last time it didn't I was wearing boots.

I've almost always been able to get it to start using a booster battery, but Walmart's tester indicates that the battery and charging system are fine. It recommends tightening connections. I did this, but still had problems for a while.

Jul 05, 2009 | 1985 Pontiac Fiero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...