Question about 1998 Mazda Millenia

1 Answer

Installing radiator remove radiator

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 706 Answers

1 - Upper seal board
2 - Radiator reservoir hose
3 - Radiator reservoir
4 - Fan motor connector
5 - Cooling fan assembly
6 - Condenser fan assembly
7 - Oil cooler hose
8 - Radiator hose
9 - Radiator bracket
10 - Radiator

installing radiator - 23901254-cld1w30nam4pvdfzfn10ykwq-4-0.jpg Car Parts Diagram

Posted on Dec 07, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the radiator on a 2007 chrysler sebring limited 3.5


REMOVAL

  1. Disconnect negative cable from battery.
  2. Remove radiator upper crossmember support. WARNING: DO NOT REMOVE THE CYLINDER BLOCK PLUG OR THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR.
  3. Drain the cooling system.
  4. Remove the radiator fans.
  5. Disconnect coolant reserve/recovery hose.
  6. Remove vapor purge solenoid from mounting bracket.
  7. Disconnect upper and lower hoses from the radiator.
  8. Remove the A/C condenser side brackets to radiator attaching screws. Separate the condenser from the radiator by lifting upward to disengage from lower mounts. Allow the condenser to rest in front of radiator.
  9. Radiator can now be lifted free from engine compartment. Care should be taken not to damage radiator cooling fins or water tubes during removal.
  10. INSTALLATION

    1. Be sure the air seal is in position before radiator is installed. Slide radiator down into position. Seat the radiator with the rubber isolators into the mounting holes provided, with a 10 lbs. force.
    2. Position air conditioning condenser onto the radiator lower mounts and install upper screws. Tighten fasteners to 5 Nm (45 in. lbs.).
    3. Install the radiator upper and lower hoses.
    4. Connect the coolant reserve/recovery hose.
    5. Connect the vapor purge solenoid to the mounting bracket.
    6. Install the radiator fans.
    7. Install the radiator upper crossmember support.
    8. Fill the cooling system.
    9. Connect negative cable to battery.

Nov 10, 2016 | 2007 Chrysler Sebring

1 Answer

Removal of radiator on a 2007 ford edge


Removal & Installation
  1. Drain the cooling system.
  2. Remove the cooling fan motor and shroud, as outlined in this section.
  3. Remove the front bumper cover, as follows:
    • Raise and safely support the vehicle..
    • Remove the 2 bolts from the top of the radiator grille.
    • Remove the 4 scrivets from the top of the radiator grille.
    • Remove the 3 lower pin-type retainers.
    • Remove the 6 fender splash shield screws (3 each side).
    • Remove the 4 lower screws (2 each side).
    • Disconnect the side marker lamp electrical connectors, if equipped.
    • Disconnect the fog lamp electrical connectors, if equipped.
    • Remove the front bumper cover.
    • Pull the corner of the bumper cover from the bracket.
  4. Disconnect the upper radiator hose and lower degas bottle hose from the radiator.
  5. Disconnect the lower radiator hose from the radiator.
  6. Lift and remove the tabs from the radiator support and position the radiator towards the engine.
  7. Remove the 2 A/C condenser bolts from the radiator and separate the condenser from the radiator. To install, tighten to 10 Nm (89 inch lbs.).
  8. Remove the radiator.
To install:
  1. Installation is the reverse of the removal procedure, noting the following:
    • Tighten the A/C condenser-to-radiator bolts to 10 Nm (89 inch lbs.)
    • Fill and bleed the cooling system.

Jul 27, 2014 | 2007 Ford Edge SEL

1 Answer

Change out cooling system radiator


RADIATOR
REMOVAL 1) Disconnect negative cable from battery. 2) Discharge the A/C system. 3) Remove the front fascia.
WARNING: DO NOT REMOVE THE CYLINDER BLOCK PLUG OR THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. 4) Drain the cooling system. 5) Disconnect the radiator fan electrical connectors. 6) Disconnect coolant reserve/recovery hose. 7) Remove A/C lines. 8) Remove the auxiliary transmission cooler hoses. 9) Remove the pushpins and the upper radiator seal.


10) Remove the pushpins and the LH and RH radiator seal (Fig. 20).

11) Remove the A/C condenser side brackets to radiator attaching screws (Fig. 22). Separate the condenser from the radiator by lifting upward to disengage from lower mounts (Fig. 22). Allow the condenser to rest in front of radiator. 12) Remove the upper and lower radiator hoses.

13) Radiator can now be lifted free from engine compartment. Care should be taken not to damage radiator cooling fins or water tubes during removal. (Fig. 21) 14) Remove the auxiliary transmission from the radiator module. 15) Remove the cooling fan assembly from the radiator module. INSTALLATION
1) Install A/C condenser, (if removed). 2) Install radiator fan assemble, if removed. 3) Install auxiliary transmission cooler, if removed. 4) Slide radiator down into position. Seat the radiator with the rubber isolators into the mounting holes provided, with a 10 lbs. force. 5) Install mounting screws. 6) Connect the cooling fan electrical connector. 7) Install the radiator upper and lower hoses 8) In the LH and RH radiator seals. 9) Install the upper radiator seal. 10) Install the auxiliary transmission cooler hoses. 11) Connect the coolant reserve/recovery hose. 12) Install the front fascia. 13) Fill the cooling system. 14) Connect negative cable to battery

Apr 02, 2014 | 2004 Chrysler Pacifica

1 Answer

I am trying to remove my radiator and place it with a new one? I have a 1998 Dodge Grand Caravan.


Chrysler Caravan/Voyager/Town and Country 1996-1999
Radiator - REMOVAL & INSTALLATION

b6c74d3.jpg

Fig. 1: Before removing the hood latch, mark it's location on the crossmember with a paint marker or other tool
  1. Disconnect the negative battery cable.
CAUTION Do not remove the radiator cap or drain with the cooling system hot and under pressure or serious personal injury can occur from hot pressurized coolant.
  1. Place a drain pan under the radiator drain. Open the radiator drain plug and allow the coolant to drain.
  2. Remove the air intake resonator from the air cleaner assembly.
  3. Remove the Coolant Recovery System (CRS) overflow tank filler neck hose.
  4. Disconnect the cooling fan electrical connector located on the left side of the cooling fan module.
  5. Remove the CRS overflow tank mounting screw from the upper radiator crossmember.
  6. Remove the upper radiator-to-crossmember mounting screws.
  7. If equipped, disconnect the engine block heater wiring connector.
  8. Remove the upper radiator crossmember.
698a0e2.jpg

Fig. 4: ... and the upper radiator-to-crossmember bolts, then ...

3723c42.jpg

Fig. 5: ... unbolt the crossmember ...

a7447b0.jpg

Fig. 6: ... and lift it from the front of the vehicle
  1. Remove the entire air cleaner assembly.
  2. Disconnect and plug the automatic transaxle oil cooler lines from the radiator.
  3. Disconnect the upper and lower radiator hoses from the radiator. Remove the lower radiator hose clip from the cooling fan module.
  4. Remove the A/C condenser mounting fasteners and separate the A/C condenser from the radiator. Be sure the condenser is supported in position.
  5. Remove the A/C filter/drier mounting bracket, 2 mounting bolts to the cooling fan module and 2 mounting nuts to the filter/drier. Remove the mounting bracket.
  6. Carefully lift the radiator out of the engine compartment. Be careful not to damage the radiator cooling fins or water tubes during removal.
To install:
  1. Be sure the air seals are properly positioned before installation of the radiator. Lower the radiator into position and seat the radiator with the rubber isolators into the mounting holes provided.
  2. Install the A/C filter/drier and mounting bracket onto the cooling fan module. Install the bracket mounting fasteners.
  1. Install the A/C condenser to the radiator.
  2. Unplug and connect the transaxle oil cooler lines to the radiator.
  3. Connect the upper and lower radiator hoses to the radiator.
  4. Connect the CRS overflow tank filler neck hose to the radiator.
  5. Reconnect the cooling fan motor electrical connector.
  6. Install the entire air cleaner assembly.
  7. Install the upper radiator crossmember.
  8. Install the upper radiator mounting screws and torque to 105 inch lbs. (12 Nm).
  9. Reconnect the engine block heater electrical connector, if equipped.
  10. Install the CRS overflow tank mounting screw to the upper radiator crossmember. Torque the screw to 18 inch lbs. (2 Nm).
96d1171.jpg

Fig. 11: Unbolt the lower radiator mounting brackets

7318707.jpg

Fig. 12: Once all of the components are removed or set aside, the radiator can be removed from the vehicle
  1. Install the air intake resonator.
  2. Refill the cooling system with a 50 / 50 mixture of clean, fresh ethylene glycol antifreeze and water to the proper level.
  3. Reconnect the negative battery cable.
  4. Start the engine and run until it reaches normal operating temperature, then check the coolant level and the automatic transmission fluid level. Add fluids, if necessary.

Hope help with this, remember comment and rated this.

Jul 22, 2010 | 1998 Dodge Caravan

1 Answer

How do i remove radiator fan from my 2004 pt cruiser?


Hope this helps!

Removal & Installation
NOTE The fan motor, fan, and the shroud are serviced as an assembly.



CAUTION Do not open the radiator draincock with the system hot and under pressure, because serious burns from coolant can occur.


  1. Disconnect negative cable from battery.
  2. Remove battery and battery tray.
  3. Drain cooling system below upper radiator hose level.
  4. Remove grille.
  5. Remove upper radiator closure panel and center brace.
  6. Disconnect upper radiator hose from radiator.
  7. For turbocharger equipped vehicles: Remove radiator inlet neck.
  8. Hoist vehicle.
  9. Disconnect radiator fan electrical connector (.
  10. Remove the two lower and left side radiator fan screws and.
  11. Lower vehicle and remove the remaining radiator fan attaching screws.

    WARNING Care should be taken not to damage the radiator cooling fins and tubes during fan removal.

  12. Remove radiator fan by lifting up from the engine compartment.

c83d6ac.gif
Radiator fan mounting points

To install:
  1. Install the radiator fan into position on the radiator.
  2. Hand-start all radiator fan fasteners.
  3. Tighten all radiator fan retaining screws to 55 inch lbs. (6 Nm).
  4. Connect the radiator fan electrical connector.
  5. Carefully lower the vehicle.
  6. For turbocharger equipped vehicles: Inspect radiator inlet neck O-ring. Replace if necessary. Install radiator inlet neck. Torque fasteners to 55 inch lbs. (6 Nm).
  7. Connect the upper radiator hose to radiator. Align hose and position clamp so it will not interfere with the engine or the hood.
  8. Install upper radiator closure panel and center brace.
  9. Install grille.
  10. Install battery tray and battery.
  11. Connect cables to battery.
  12. Fill cooling system.

Apr 18, 2010 | 2004 Chrysler PT Cruiser

1 Answer

What is the procedure for removal of the radiator from the Mercury Mystique(1998 model)?


Ford Contour/Mystique/Cougar 1995-1999 Repair Guide

Radiator -REMOVAL & INSTALLATION
(see Figures 1 through 7)

7249321.jpg
Fig. 1: Remove the upper radiator hose from the radiator


d2d2436.jpg
Fig. 2: Use a back-up wrench to remove the transaxle cooler line connections-automatic transaxle only


3213ac8.jpg
Fig. 3: the lower transaxle cooler line connection


ec9272d.jpg
Fig. 4: Remove the passenger side radiator mount and ...


956cd3d.jpg
Fig. 5: ... and the driver's side radiator mount


f06fec0.jpg
Fig. 6: The condenser can be support using mechanic's wire as shown here, or another suitable device


242d821.jpg
Fig. 7: Carefully lower the radiator out the bottom of the vehicle
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Remove the upper radiator hose from the radiator.
  4. On 2.5L equipped vehicles, remove the radiator overflow hose from the radiator.
  5. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler inlet fitting and plug the line and the fitting.
  6. Remove the engine fan.
  7. Raise and support the vehicle.
  8. Remove the lower radiator hose from the radiator.
  9. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler outlet fitting and plug the line and the fitting.
Remove the cooler lines while holding the radiator connector with a back-up wrench.
  1. Support the radiator, and A/C condenser with a jackstand or other suitable device.
  2. Remove the lower radiator supports from the front of the subframe.
  3. Remove the two retaining bolts for the A/C condenser from the brackets at the bottom of the radiator.
  4. Position the jackstand aside and remove the radiator out the bottom of the vehicle.
To install:
  1. Carefully raise the radiator into place and support the radiator with a jackstand or other suitable device. Install the two retaining bolts for the A/C condenser into the brackets at the bottom of the radiator.
  2. Install the lower radiator supports and tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  3. Remove the jackstand and install the transmission cooler outlet line (if equipped) and the lower radiator hose to the radiator.
  4. Lower the vehicle.
  5. Install and tighten the fan shroud nuts.
  6. Install the transmission cooler inlet line (if equipped) and the upper radiator hose to the radiator.
  7. On 2.5L equipped vehicles, install the radiator overflow hose from the radiator.
  8. Connect the negative battery cable.
  9. Fill the cooling system with the proper 50 / 50 mixture and start the vehicle.
  10. Bleed the cooling system and check for leaks.

Hope helps with this (remember rated this help) Good luck.

Jan 20, 2010 | 1996 Mercury Mystique

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

2 Answers

Radiator replacement


  1. Remove air cleaner and duct assembly.
  2. Drain the coolant.
    1. Remove the engine mount struts.
    2. Remove the cooling fans with the cooling fan shroud.
    3. Remove the radiator upper hose from the radiator.
    4. Remove the radiator lower hose from the radiator.
    5. Disconnect the transaxle oil cooler lines from the radiator.
    6. Remove the radiator brackets and bolts.
    7. Remove the radiator. Installation Procedure
    1. Install the radiator. Notice: Refer to Fastener Notice in Service Precautions.
      1. Install the radiator brackets and bolts.
        • Tighten the bolts to 24 Nm (18 ft. lbs.) .
      1. Connect the transaxle oil cooler lines to the radiator.
      2. Install the radiator upper hose to the radiator.
      3. Install the radiator lower hose to the radiator.
      4. Install the cooling fans with the cooling fan shroud.
      5. Install the engine mount struts. Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) coolant. If Coolant other than DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) is added to the system the engine coolant will require change sooner; at 50,000 km (30,000 mi) or 24 months.
      6. Fill the cooling system.
      7. Install the air cleaner and duct assembly.

Jun 28, 2009 | 2000 Chevrolet Venture

1 Answer

Radiator replace


I Hope you Find this Helpfull And Please Remember to RATE ME

  1. Drain the coolant.
  2. Disable the SIR.
  3. Move the forwarding discriminating sensor out of the way.
  4. Remove the air cleaner assembly.
  5. Remove the cooling fans.
  6. Disconnect the radiator inlet hose from the radiator.
    1. Disconnect the radiator outlet hose from the radiator.
    2. Disconnect the engine oil cooler lines from the right radiator end tank.
    3. Disconnect the transmission oil cooler lines from the left radiator end tank.
    4. Remove the left and the right engine torque struts.
      1. Remove the upper radiator support screws.
      2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
        1. Install the radiator to the vehicle.
        2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
        3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
        4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
        5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
          1. Connect the radiator inlet hose to the radiator.
          2. Install the cooling fans.
          3. Install the air cleaner assembly.
          4. Install the forward discriminating sensor.
          5. Enable the SIR.
          6. Refill the coolant.
        6. Hope this Helps and PLEASE RATE ME

Jun 03, 2009 | 1998 Cadillac DeVille

Not finding what you are looking for?
1998 Mazda Millenia Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...