Question about 1993 Ford Ranger SuperCab

1 Answer

93 ford ranger 3.0 wont start and when you turn the ignition no power

And when you turn the ignition to start it all the lights turn off and no power. wait 30 seconds everything comes back on.(lights, horn)

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 205 Answers

Try changing the main relay

Posted on Mar 24, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: 2003 Ford Ranger won't start

it can happen from a various of reason How about an alternator.if it not check the fuel pump. check the distributer cap and spark plugs.. If the car doesn't turn over then you might want to take it into the shop. Check also the solenoid.

Posted on Jun 22, 2008

  • 17 Answers

SOURCE: 1993 FORD RANGER 4 WHEEL DRIVE

there is an actuator on the back of the transfer case that likes to fail odds are this is where your problem is. check power and ground here and if you have both replace the actuator

Posted on Dec 01, 2008

  • 79 Answers

SOURCE: After starting, the starter stays ingaged (GRIND)

shim the starter it sounds like it is staying engaged to the flywheel try shiming the starter

Posted on Mar 22, 2009

cadman000
  • 607 Answers

SOURCE: 1991 ford ranger wont start

I do believe the FORD is located under ther hood either on the firewall or on L/S wheel housing. Have encountered many , many faulty control modules. There came a time if you came across a Ford product with a no start, you automatically suspected it, and 90% of the time you were right.

Posted on Apr 01, 2009

  • 750 Answers

SOURCE: Ford ranger not starting

check the main fuse, and relay, if ok check for power to the starter solynoid if yes then starter may be faulty. check power to switch also

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The engine just dies when going down the road and when I try to re-start, the motor won't turn over. Why is this happening?


You didn't tell us is you have the 4 banger, 3.0 or 4.0 V6 engine.

The engine can stall for a number of reasons. For a engine to run it requires air, fuel, compression, and spark at the proper time. I doubt air is the problem. The fuel pump may be cutting out (bad pump, bad relay, bad pump wiring inside the tank (my 93 3.0 Ranger had the last issue). The engine stall could be a lack of fire to the plugs. A bad (cracked) coil, ignition module problem, EFI computer or wiring problem, or maybe an ignition switch problem. The starting system is somewhat isolated and pretty much separate from the ignition system in general. This makes me suspicious of your ignition switch.

Mar 08, 2015 | 2000 Ford Ranger SuperCab

3 Answers

Truck turns over and starts when I connect battery???? No key is even in the ignition.


Maybe the ignition is bad- or your starter solenoid stuck in engaged position?

Mar 29, 2013 | 2000 Ford Ranger SuperCab

1 Answer

How do you get a 93 ford ranger ignition to pop out? its bad and i have a new one to put in


There should be a pin hole on the same face of the ignightion key. you push a pin that will fit in the hole and push the key in while swithching it backwards. hope this helps it's been a while

Jul 21, 2012 | Ford Cars & Trucks

1 Answer

A plastic piece in the ignition broke off now power wont cut off


sound like the ignition switch went bad or broke apart.

Oct 10, 2009 | 1993 Ford Ranger SuperCab

1 Answer

I have power but my 1990 ford ranger clicks loudly and wont turn


Starter could be stuck..
If you are SURE you battery is fully charged with no dead cells..
Try --
(takes 2 peopl) -
Turn the key like you are trying to start it.
At the SAME time - smack the starter with a small hammer not too too hard..
Let me know what happens..

Jul 09, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Replaced wiring harness on 2000 Ford Ranger now truck won't start


2000 ford ranger wont start off switch if u jump the silanoid it will start. new start and ignition switch

May 06, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1999 ford ranger 4 wheel drive 5 speed won't start


i had a 93 ranger, same thing happend to me. Ended up it was the little switch on the cluch pedal. when they pushed the clutch in their foot kicked it off. Its just a clip on spring on the arm of the pedal.

Jan 03, 2009 | 1999 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger


TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Jun 11, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...