Question about 1995 Ford F150 Styleside Regular Cab

1 Answer

I have a 1995 F-150 4.9 L it is very hard to go into first gear.and when you take off it still hard to go into 3,4,5,gears

I have a hard time putting this truck in first gear or reverce.when I finely get it into first gear I take off,and it still has problems going into 2,3,4,gears.the clutch pedal feels hard.(normal)when in first gear and with pedal pushed down,the truck doe's not try to go forward.unless I release the clutch pedal.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

Check clutch cylinder please

Posted on Mar 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
aliensanity
  • 24 Answers

SOURCE: clutch pedal not returning to position

Under the dash look to see if there is a spring attached to the petal or maybe under the hood. Or you might have something getting in the was of the petal arm. Good Luck and PEACE

Posted on Jun 13, 2008

  • 3 Answers

SOURCE: 1979 ford f350 clutch pedal travel 1/2 inch

sounds like the clutch armerature may be hanging or broke. it's the rod that ingages the clutch.

Posted on Apr 17, 2009

co7196
  • 3433 Answers

SOURCE: clutch sticks in transmission won't go into gear

Clutch is out of adjustment

Posted on Oct 06, 2009

  • 123 Answers

SOURCE: I am unable to put my 2001 Ford Escape xls into

that is your clutch pump/cable in not functioning. u need to check the fluid level (if your car using hydraulic clutch) or your clutch cable broke...

Posted on Nov 19, 2010

  • 4369 Answers

SOURCE: just put in new clutch

what you mean is the clutch is not disengaging the transmission from the engine, so you can shift it.

This is always due to air trapeed in the clutch system. It is very hard to purge the air.

You may have to have a shop use their evac/fill equipment, if they have it.

Try raising the front of the truck as high as you can, including facing uphill. The air is likely trapped at the slave cylinder, not at the clutch.

There is a video on you tube showing a guy purging air from a Ranger. See if you can view it.

1) The Hydraulic system should be bled to remove all the air whenever air enters the system. This occurs if the fluid level has been allowed to fall so low that air has been drawn into the clutch master cylinder. Under normal circumstances, air should not enter the system when the quick disconnect hydraulic line fittings have been disconnected. The procedure is very similar to bleeding a brake system, but depends mainly on gravity, rather than the pumping action of the pedal, for the bleeding effect.

2) Fill the master cylinder to the top with new brake fluid conforming to DOT 3 or DOT 4 specifications. Caution: Do not re-use any of the fluid coming from the system during the bleeding operation and don't use fluid from which has been inside an open container for an extended period of time.

3) Raise the vehicle and place it securely on jack stands or drive it securely up on ramps (whichever method you chose) to gain access to the bleeder valve, which is located on the top left side of the bellhousing (See Illustration 1-1 below). Try to keep the truck as level as possible. Caution: Don't forget to chock the rear wheels and set parking brake for extra safety...

4) Remove the dust cap which fits over the bleeder valve and push a length of clear plastic hose over the valve. Place the other end of the hose into a clear container.

5) Open the bleeder valve. Fluid will run from the clutch master cylinder, down the hydraulic line, into the release cylinder (the Slave Cylinder) and out through the clear plastic tube. Let the fluid run out until it is free of bubbles.
Note: Don't let the fluid level drop too low in the clutch master cylinder, or air will be drawn into the hydraulic line and the whole process will have to be started over.

6) Close the bleeder valve.

7) Open the bleeder valve and have an assistant slowly depress the clutch pedal allowing fluid to flow through the clear plastic hose. When the clutch pedal is almost to the floor, close the bleeder valve and have the assistant release the pedal.

8) Slowly press the pedal five times, waiting two (2) seconds each time the pedal is released. When releasing the pedal on this step, release it fast. This tends to help **** fluid down the stream and aid in faster bubble reduction.

9) Fill the fluid reservoir to the top.

10) The clutch should now be completely bled. If it isn't, (indicated by failure to disengage completely, and a soft or no pedal), repeat steps 5 through 9.

11) Continue this process until all air is evacuated from the system, indicated by a solid stream of fluid being ejected from the bleeder valve each time with no air bubbles in the hose or container.

12) Install the dust cap and lower the vehicle. Check carefully for proper operation before placing vehicle in normal service. Check the fluid level.

Note: If you can NOT get fluid out of the bleeder screw, then the internal check valve in your clutch master cylinder may be stuck, or you haven't bleed the system for at least 30 minutes. You will either have to use a different bleed technique, or replace the clutch master cylinder. Bleeding a Ranger clutch system takes time and patience. One small mistake / loss of patience / or shortcut, and you'll have to start all over.

Posted on May 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It's not hard to start..it's hard to go in 2 and 3 gear


After start go to D and then to 3 and 2. Usually 3 should get you enough power up or down a hill. What is hard about changing gear?
WHAT vehicle is it?

Jul 20, 2013 | Cars & Trucks

3 Answers

Transmission in chevy silverado 1500 5.3L v8 will not shift from 2-3 gear transmission has been rebuilt and 2-3 shift solenoid was changed but still will not shift from 2-3 gear


For gear shift issues and gear stuck issues,the help links are provided below. Click the link below to go through troubleshooting procedure:---- ---- Car will not move when in gear?


http://repairhelpcenter.blogspot.in/2012/02/car-will-not-move-when-in-gear.html ---- transmission sticks in first gear? http://technoanswers.blogspot.com/2012/01/mercedes-benz-transmission-sticks-in.html ----- Transmission not engaging in first gear? http://technoanswers.blogspot.com/2012/01/mercedes-benz-not-engaging-in-first.html ----- Vehicle only goes in First gear?

http://howtobyme.blogspot.com/2011/11/chrysler-pt-cruiser-only-goes-in-first.html


----

Car is stuck in park and the shift will not move?

http://howtobyme.blogspot.com/2011/08/car-is-stuck-in-park-and-shift-will-not.html


---- Engine will not go out of park mode? http://technoanswers.blogspot.in/2012/02/2002-nissan-sentra-will-not-go-out-of.html ---- Car stuck in park? http://technoanswers.blogspot.in/2012/02/nissan-sentra-stuck-in-park.html ----- Car will not come out of Park?

http://howtobyme.blogspot.com/2011/11/car-will-not-come-out-of-park.html

-----
Automatic transmission will not go into high gear?

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html
--- Car wont downshift sometimes?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-downshift-sometimes.html
---- Transmission will shift into drive?

http://schematicsdiagram.blogspot.com/2011/12/buick-park-avenuetransmission-will.html
----- Auto wont shift from park? http://schematicsdiagram.blogspot.com/2011/12/ford-taurus-wont-shift-from-park.html ---- Car Transmission will not go into Park mode?

http://schematicsdiagram.blogspot.com/2011/12/car-transmission-will-no-go-into-park.html
----- Shift indicator directly goes to 2nd when key is turned ON?

http://schematicsdiagram.blogspot.com/2011/12/shift-indicator-directly-goes-to-2nd.html
---- Third gear missing and engine losing power?

http://schematicsdiagram.blogspot.com/2012/01/third-gear-missing-and-engine-losing.html
------- Vehicle has whining sound in gear?

http://technoanswers.blogspot.com/2012/01/chevrolet-silverado-has-whining-sound.html
----- Hard to shift gears on Manual transmission?

http://technoanswers.blogspot.com/2012/01/hard-to-shift-gears-on-manual.html
------ Car hard shift at slow speeds?

http://technoanswers.blogspot.com/2012/01/car-hard-shift-at-slow-speeds.html
--- Automatic transmission shift lever hard to move on cold mornings?

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html
------ Gear shifts hard?

http://schematicsdiagram.blogspot.in/2012/02/2000-nissan-maxima-shifts-hard.html
------- Vehicle noticed sluggish delayed shifts while driving?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-noticed-sluggish-delayed-shifts.html

-------

This will help.

Thanks.

Mar 14, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

My suburban with 4l60e wont shift out of 2nd gear. when you put it in drive, it does fine til time to go into 3rd. it seems to just go into neutral, letting the rpms fly so i just put it in 2nd gear and...


The check engine light should be on. With a scanner pull the transmission control codes. and follow up on their leads speed sensers ( thiers 3 and shift soliods ( thiers 4) the connectors and the wires and more likly to be a problem than hard parts as this transmission is thris on up shifteed sllectonically

May 09, 2011 | 1999 GMC Suburban

1 Answer

I bought a 1999 jetta volkswagon for my 15 year old son turning 16 next month. The previous owners put a used engine (2000) with 63,000 miles. the car itself has 180,000. I have no problems ******* from 3,...


When you install an engine, you don't "line up" gears. It's likely that either you have a worn shift fork or synchro (both inside the transmission).

Jul 08, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

Shifter takes a lot of wiggling n shifting to go in gear


sounds like you need to replace the shifter tube and bushings this is very common problem its not a very hard job to do if you are mecanicly inclined let me know if you need detailson how to replace

Jun 05, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Hyundai gear box


sounds like you are low on gear oil

Jun 03, 2009 | 1994 Hyundai Excel

1 Answer

Transaxle fluid


you can remove the speedometer gear put oil untill you see oil in trasmission or when you put the gear back in and the oil touch the gear notice be carefull sometime the gear is hard to remove because of corosion that the only place you can fill it hope it help you good luck pierre

Jul 01, 2008 | 1994 Mazda MX-3

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...