Question about 1989 Oldsmobile Cutlass Supreme

1 Answer

Drivers door When I pull on doee handle door will not open

Posted by on

  • leo_carpente Jun 15, 2009

    Rods are still connected. I have done the open door from inside from passenger side

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

The rod may have fallen off the outside handle inside of the door. try opening the door from the inside for now.

Posted on Jun 15, 2009

  • Kelly C Bundy II Jun 15, 2009

    the Handle itself may have broken. i think they're cast from pot-metal. GM proucts are vulnerable to this. the handle and door guts will need replaced.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove outside handle on driver's door on 2012 s60


On a S60, 2012, (drivers door) you first remove the plastic cover in under which you find the lock (with keyhole).
secondly, open the door and remove the 15 mm diameter plastic cover near the handle. Insert a long torx scrwdriver(T25 ?) in the
opening and while keeping the door handle "open" (this gives you the possibility to easily replace the handle later) Turn the torx until it stops
(do not use much force). Now you can pull out the metallic lock, peer
out the small white plastic under the door handle and pull out the handle. Do not turn the torx before you have replaced the handle.

In the case of back door, you start by finding the hole for the torx under the doors rubber sealing near the door handle.

Jan 08, 2013 | Volvo S60 Cars & Trucks

1 Answer

The outside drivers side door handle on my 96 bravada is about to pull away from the door how do i fix this?


Open your door. on the latch side of your door near the top by the back of the window you will see a rubber plug about the size of a nickel remove it and the handle bolt is inside the holethe other bolt you will have to remove inside door trim panel. if they are both ok you will have to perchase a new handle.

Jan 18, 2012 | 1996 Oldsmobile Bravada

1 Answer

Trying to replace the driver's side door handle; the door shut and won't open. I can't get the panel off to adjust the handle because the door is closed!


take the scerw out of inter door handle then take the pull handle to shut the door off then the pull the door skin off it pops off then there is a rod that runs to the lach u pull it the door will open

Mar 17, 2011 | 1992 Nissan Pickup

2 Answers

Latch on driver door is closed door will not latch closed


Pull the door handle and with a screw driver pry the latch to open at the same time.

Feb 27, 2011 | 1993 Chevrolet Lumina

1 Answer

Unable to open driver side door with inside latch on my 1997 chevy suburban. How to take off inside panel to see mechanism? Outside handle open the door okay.


take the bezel off around th door handle. take the screw out of the armrest. pull out the window switches and pull out on the door handle and pull up .disconnect the last two plugs then you can see the whole door handle

Jun 04, 2009 | 1997 Chevrolet Suburban

1 Answer

Drivers door handle will not open door. how does the panel come off


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

May 30, 2009 | 2001 Volvo S60

1 Answer

Driver door panel removal and re-connect door pull


You most likley have a damaged inside door handle. To remove the door panel, you must first remove the handle bezel. The trim piece around the handle. It is held in place by 4 retainer tabs, take a small flat screw driver, insert it between the bezel and handle. Gently pry away from the handle. If you look in the crack around the handle you will see the tabs. When you get that off, remove the switch assembly by prying up on it gently, unplug the wiring. There are 2 screws in the door panel where you pull the door shut, remove those also. Start at the bottom front of the door panel, pull outward firmly, but not violent. The retainers will come out, you will most likley break some, this is common. The inside handle is about $45 from your dealer. If it is the handle it is held in with 1 rivit, drill it out with a 3/16 drill. Replace the handle, reassemble. Good Luck.

May 05, 2009 | 2000 Cadillac Escalade

1 Answer

Drivers side door on my jeep cherokee will not open from inside


most likely the inner door handle has a broken hooking tab for the rod to the latch plate.most door panels are held in place with a few screws around the door pull handle and arm rest than most of the sides and bottom of the door panel are held by plastic snap clips. with a large straight blade screw driver start at a corner of the door panel , slide the blade of the screw driver under the edge of the panel and lightly pry out untill you lossen up one of the clips than slide along the screw driver to the next clip , keep going till the panel is lossened up.

Mar 29, 2009 | 2000 Jeep Grand Cherokee

4 Answers

Drivers side door, not opening


VERY common issue.. the handle being replaced is ok.. but the actual metal rod that connects it to the latch needs bent a little to make it more responsive, what happens is over time this rod (which is bent slightly) will straighten, and the operator pulls harder on the handle which eventually brakes.. then replacing the handle will solve it for a while, until the trend repeats itself... VERY common, I have fixed hundreds in the shop so far...

Jul 10, 2008 | 1999 GMC Suburban

1 Answer

Door handle loud pop- won't open front driver door


hi yes there is a plastic clip that holds the the door handle rod to the handle and connects to the lock you should be able once the pad is off take the bolts out of the door lock it will drop down so far as you can get at the door handles retaining bolts and the clip itshelf you should be able to replace the clip without taking the handle out bit fiddley but not that difficult yates210456

Jun 27, 2008 | 1999 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...