Question about 1987 Ford Ranger

Open Question

How to adjust 87 ford ranger tie rod

Tie rod ajustment

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

Ad
Murphybanton
  • 2004 Answers

SOURCE: inner tie rod end on passenger side needs replaced

You will definately need an expert to handle this because it is in a tight compartment.

Good luck.

Posted on May 27, 2009

emissionwiz
  • 76164 Answers

SOURCE: Cost to have shop replace tie rods on 2000 ford taurus

$200 for labor, parts vary.

Posted on Jun 18, 2009

Zeevert
  • 373 Answers

SOURCE: 2002 ford escape tie rod squeaks

My outer tie rod did the same thing when just out of warranty. I could tell it was "bad" by putting my hand on the tie rod while someone else turned the steering a little and I could easily feel the vibration.
Check the other side to feel the difference. Tie rods don't cost that much, if you can replace it yourself, and take a chance on foregoing the wheel alignment. Maybe a $150? job at the shop.
In my case, a tie rod was not readily available. I verified that it was a good joint; no shake or rattle. Then I squirted a little WD40 inside the boot, and put it back together. 70,000 miles later, the new tie rod is still on my shelf waiting for the squeak to return.

Posted on Mar 17, 2010

  • 5 Answers

SOURCE: reset throttle position sensor on 87 ford ranger

1988 Ford Ranger 4x4 2.9L throttle senor resistence from Idle of 1.0 full throttle 5.0. How do I measure the resistence?

Posted on Mar 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Ford ranger shakes at 45 mph until I let off the gas. I drive a little further and it starts shaking again until I let off the gas. Drive more, shakes, let off the gas. Still shakes.


Have the front end checked for worn parts like suspension rubber bushings and worn tie rod ends or ball joints, all will cause this

Nov 22, 2016 | 2001 Ford Ranger

2 Answers

Why inside wear tire Ford Ranger 2004


Worn Suspension Parts--camber negative-tilted in at top

Low Tire Pressure

Never Rotate Tires

Hit Something & knocked out the toe or worse

Toed in too much

Worn Steering Rack

Worn ties rod ends-outer or inner on rack

Stabilizer Bushings
Springs
Shock/Struts
Ride Height -off

Aug 14, 2014 | Ford Ranger Cars & Trucks

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

How do i adjusting steering box 1998 ford ranger


Your steering adjustments are in your tie rod end adjustment. Bring it to an alinment shop and they could straiten your wheel by putting an alinment on it. it is realy difficult to do this if you have not done this you might be able to pull the steering wheel off with the wheels straight and reposition it on the steering spindle you will need a steering wheel puller to do this.

Feb 28, 2011 | 1998 Ford Ranger SuperCab

1 Answer

Does a 87 ford ranger have a selfadjusting clutch?


It should be a self adjusting from OEM but you can run either type. I am running a non self adjusting in my 96 ranger 2.3l and have had no problems. The only thing to remember is when you change the clutch you have to bleed the hydraulic system. http://www.youtube.com/watch?v=HgNTDGwcjZc This is a great video on how to bleed the system.

Jan 13, 2011 | 1987 Ford Ranger

1 Answer

How do i take the timeing belt of a 87 ford ranger


The 87 Ford Ranger 2.9L is chain driven. They dont have a timing belt. Now the 2.3L 87 Ranger were belt driven.

Sep 16, 2010 | 1987 Ford Ranger

1 Answer

I have no sway bar on my 89' Ford F-150 4X4


Many older Ford trucks with lower trim levels did not have rear sway bars. I have an 87 Ranger XLT that has a rear sway bar, my one buddy has an 88 XL without one. Both truck suspensions are stock.

Oct 03, 2009 | 2003 Ford E250

3 Answers

Reset throttle position sensor on 87 ford ranger


Ok in the Haynes Repair Manual it say that the TPS sensor is non adjustable on a ranger. Now if you have an adjustable one you have a TPS block that you use to set this sensor. The best bet is to line up the slot in the TPS with the blade on the throttle shart.

Reference Haynes Repair Manual Page 6-8

Mar 28, 2009 | 1987 Ford Ranger

1 Answer

Tie rod adjustments


Loosen the locknut and turn the Inner tie rod end , it has a ball and socket inside the steering rack boot. remember to tighten the locknut after servicing !

Dec 18, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...