Question about 1980 Mazda 323 1.5

Open Question

4g32 engine What is the correct oil pressure for this engine

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for workshop manual,(Chrysler galant (aus) Mitsubishi engine Saturn 4G32 1976,2nd gen


Try WWW,faxonautolit.com
1-800-458-2734
Inquries - 951 - 786 -4177
Owners / repair parts / sales manuals

May 23, 2016 | Mitsubishi Cars & Trucks

1 Answer

Engine oil light flashing


Flashing oil light indicates a loss of oil pressure. No oil pressure will cause the engine to seize up. Check the oil level, if full verify that the oil sending unit is connected correctly. Listen for unusual engine noise (Shut down immediately to avoid damage to the engine), connect an oil pressure gauge to the oil sending port (remove sending unit) and verify oil pressure. the issue could be a loose connection, broken connection or plugged sending unit, as well as loss of oil pressure.

Sep 01, 2015 | Cars & Trucks

1 Answer

Caterpillar 330cl c-9 engine ecm reading low oil prressure and the manual guage shows the correct pressure


change the oil pressure sending unit on the eng. if this goes bad it sends the wrong voltage to the computer which will then detune the engine to reduce the chance of damage due to low oil pressure . Good Luck

Feb 25, 2014 | 2002 Oldsmobile Bravada

1 Answer

Recommended spark plugs for a 4G32 engine


Not sure here as its been a long time since i done one but i seem to +remember it having different plugs but i just dont remember so ask at the dealers ,i know the alfa twin spark uses two different type of plugs in each cylinder but the mitsubishi ? sorry been a long time maybe 20+ yrs ago

Dec 19, 2012 | Dodge Cars & Trucks

1 Answer

Low presure oil


first thing check is the engine oil level.if oil level okay check oil pressure should be for the 4.2 engine oil pressure should be 12 psi @ 1200 rpm for the 5.3 oil pressure should be 18 psi @ 2000 rpm if oil pressure good problem in the oil pressure sending unit. if oil pressure is low problem faulty oil pump or worn crankshaft bearings if oil pressure low engine will have rod knock.make sure you are using correct oil viscosity if oil too thick you will have low oil pressure oil too thin you will loose oil pressure.

Nov 26, 2012 | 2004 GMC Envoy

1 Answer

2005 grand Prix oil pressure light an dinging comes on


1. Check your oil level. If oil level is not ok, correct oil level and find out why oil level was low and correct the problem. (Leaks, bad PCV, Burning oil due to severe engine wear, nobody has bothered to check it for the last 3000 miles, WAY overdue for an oil change, etc.) If oil level is ok, proceed to next step.

2. Remove the oil pressure sensor and install a manual oil pressure gauge. Run engine to verify low oil pressure. If gauge shows that the oil pressure is low, overhaul or replace engine. If oil pressure is ok, replace oil pressure sending unit and retest.

Mar 06, 2012 | 2005 Pontiac Grand Prix

1 Answer

What causes high oil pressure reading 1990 toyota pickup?


Probably a faulty oil pressure relief valve.

If not done already, you should have an independent oil pressure gauge hooked up to the lube system by a mechanic to check that the high oil pressure reading you are getting is correct. Before doing this change the engine oil and the oil filter and ensure you use the correct oil and only fit a quality and correct spec oil filter.

Sep 08, 2011 | 1990 Toyota Pickup

1 Answer

Have a 2003 toyota corolla and oil pressure light came on we changed oil and now its on again what could it be?


If you just changed the oil, therefore we can assume that the oil level is correct at this time and that the correct oil viscosity (5W-20 or 5W-30) was used. Are there any unusual noises coming from the engine? Like, maybe "tapping" or "squeaking" sounds? If so, then the oil pump may have gone bad and is not supplying adequate oil pressure to the engine. Continued use of the vehicle can result in serious engine damage. Have the oil pressure checked by a shop ASAP.

If the vehicle is running normally and no unusual noises are heard, then the oil pressure sensor (a.k.a. oil pressure sending unit) may be sending a false signal to the dash "idiot light". Replace the oil pressure switch.

Hope this helps.

Have a Nice Day !!!

Apr 15, 2011 | Toyota Corolla Cars & Trucks

1 Answer

What is the correct oil pressure for 2000 grand jeep cherokee larado its about 75 now. i want to buy this car but worried about the oil pressure.


Normal oil pressure should be between 40 and 60 psi. A cold engine will normally have higher pressure. If you're seeing 75 psi on a warm engine I would recommend having the pressure checked with a manual gauge to verify the gauge in the Jeep is working correctly. If the gauge is correct oil viscosity may be too high (oil too thick) or there may be a problem with the oil pump pressure relief valve. If the gauge is not correct the sending unit may be at fault.

Apr 09, 2011 | 2000 Jeep Grand Cherokee

2 Answers

My stop light keeps coming up with the problem oil pressure,i have a golf gti turbo


Get the oil pressure tested with an outside gauge. If you run short of oil pressure, turbo and engine will suffer, as you know....

If you are actually short on pressure, you would need to investigate further, usually no good answers there....

But commonly a transducer fails and gives wrong readings, hope for this result

Sep 11, 2009 | 2001 Volkswagen Golf

Not finding what you are looking for?
1980 Mazda 323 1.5 Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...