Question about 1995 Mercury Villager

Open Question

Idle control sensor

Replace idle control sensor

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whenever I let my 2010 toyota camry sit for several hours, it makes a winding noise and idles high when I first start it up. What could be causing this.


starter problem

2010 Toyota camry use hi torque starters

will wind over faster .
.if noise is very audible
have starter checked over or rebuilt or replace

idle problem
local weather conditions and old 02 sensors can cause hi idle
motor idle is controlled by the idle control sensor ( IAC) and can be cleaned
..if solenoid part is faulty ..non adjustable trow away part
replace unit


26303730-ppcntsxlnlgi0v2ejwpzo3sw-2-0.jpg

26303730-ppcntsxlnlgi0v2ejwpzo3sw-2-1.jpg

Oct 07, 2016 | Toyota Cars & Trucks

1 Answer

I changed the idle control valve still don't idel could i have a bad tps sensor


Black smoke usually means burning too much gas. The problem is the IAC idle air control. I would also replace the TPS

Jun 07, 2017 | 2002 Kia Optima

1 Answer

Problem with idle


hi,
-please clean the throttle manifold,
- replace idle air control
- check the tps
-check MAP sensor if feeted.

Mar 05, 2014 | 1992 Chevrolet Cavalier

1 Answer

When I start the car the engine idles, but as soon as I put it in drive, the engine shuts off..


try the idle control sensor.is your check engine light on? if you do replace the idle control sensor,make sure you disconnect the positive cable from battery for 10minutes to allow the computer to adapt the new sensor to the system. when reconnected,that check engine will go off. the idle control sensors easily replaced,2bolts 1 plug in before replacing it,disconnect the positive cable on battery, then by the time it's replaced, the system will reset to adapt the new component. look on top of the engine for a round silver component that has one plug in to it. it will be where the air flow goes into the engine. 2bolts. one plug in. replace that. it's the idle control sensor. if you have doubts,take it by autozone or advance auto or wherever you purcahse the part and have the clerk point it out for you. thank you for choosing fixya.com

Jan 23, 2011 | 2001 Jeep Grand Cherokee

1 Answer

1990 ciera 3300 v 6 is stalling at idle and when backingup could that be a vacume problem


I would clean or replace the ISC (idle speed control) sensor, this sensor is what controls the idle speed of your engine.The sensor screw in to the side of the throttle body.will have a four wire harness connector going to it.

Aug 19, 2010 | 1990 Oldsmobile Cutlass Ciera

2 Answers

97 malibu wont idle/replaced sparkplugs 2-idle ssensors had coil pack checked out,ok/still wont idle whats up please?


The throttle position sensor,and the idle air control valve would be my guess at this point.Ohm out the throttle position sensor,to see if it has a dead spot,if so,replace it,if not,replace the idle air control.

Nov 13, 2009 | 1997 Chevrolet Malibu

2 Answers

Low idle almost dies


http://www.fixya.com/ThreadView.aspx?thid=2533916&prdid=698832

Problem fixed
Thank you!!!!!!!!

Jul 06, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Car idles up and down, and also stalls


EGR valve and evp sensor controls idle. Replace both it should fix the idle problem

Jun 15, 2009 | 1993 Ford Explorer Limited

1 Answer

High idle speed


Replace the sensor.

May 21, 2008 | 1995 Ferrari 355

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...