Question about 1998 GMC Sierra

1 Answer

Remove and replace starter - 1998 GMC Sierra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • GMC Master
  • 2,007 Answers

Disconnect the negative battery cable. Remove the starter bolts. Pull it out, and down so you can access the wires. Pay close attention to how they are hooked up, and positioned. You're going to want them back on the same way. Remove the wires, and then hook the wires to your new starter, put it up in position, bolt it, hhok your battery cable up again.

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 pontiac montana and am trying to figure out how to change the starter.


STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.
  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.


  3. Remove the starter motor BAT terminal nut and electrical leads.
  4. Remove the starter motor S terminal nut and electrical lead.
  5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  6. Remove the starter motor bolts.
  7. Remove the starter motor.

Installation Procedure



  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in Cautions and Notices.
  3. Install the starter motor bolts.Tighten:
    Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
  4. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  5. Install the starter motor S terminal electrical lead and nut. Tighten:
    Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
  6. Install the starter motor BAT terminal electrical leads and nut. Tighten:
    Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Aug 05, 2016 | 2001 Pontiac Montana

1 Answer

Replace starter


Starter Replacement
Removal Procedure
Caution: Before servicing any electrical component, the ignition and start switch must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
    alt="Object Number: 217186 Size: SH">
  3. alt="Click here for detailed picture of above image.">
  4. Remove the positive battery cable starter motor lead nut (1) from the starter.
  5. Remove the positive battery cable lead from the starter.
  6. Remove the starter solenoid terminal lead nut (2) from the starter.
  7. Remove the starter solenoid terminal lead from the starter.
    alt="Object Number: 217190 Size: SH">
  8. alt="Click here for detailed picture of above image.">
  9. Remove the starter motor bolts (2, 3).
  10. Remove the starter motor (1).

Sep 23, 2015 | 2000 Cadillac Catera

1 Answer

How to replace starter motor


Remove the battery connection ground, lift the vehicle with a jack on the side starter is on and block the under the frame for safety, take the starter cable off the solenoid and remove the starter wire from solenoid, remove the bolts holding the starter on and drop the starter out. This starter is not heavy, but it will be over your head so don't drop it. Replace the starter in this same way by putting the new starter in and tightening the bolts, then hook the starter wire back on the small stud on solenoid and the cable to the large stud. Let it down on it's tires and hook the battery back up and your done.

Nov 23, 2014 | 2007 Mitsubishi Outlander 3.0

1 Answer

Starter removal


remove battery terminals to prevent unexpected grounding of wires at starter. Remove wires at starter, taking note of how they are placed on the starter/selonoid... remove starter mounting bolts, remove starter. Get new starter and install same as reverse. Sometimes the starter has exhaust or other things in the way, so you may have to turn the starter just a certain way to remove it. Might have to come out the top, but out the bottom is the most common way to remove the starter. replace battery wires and vroooom.. off you go.

Dec 17, 2013 | 2002 Hyundai Santa Fe

1 Answer

Starter replacement 2006 PT Cruiser


you need to turn off radio first then remove negative battery cable,then from under the hood,you need to remove air cleaner box cover and remove engine structural collar then you can remove starter electrical connector and starter bolts and starter.

Sep 18, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Removal and installation of starter of 2002 mercury mountainer


Here's the generic starter replacement directions.
Engine should be cool, parked on level surface. Remove negative cable from battery. Remove electrical connections at starter (Sometimes starter may need to be partially removed to access all electrical connections.) Remove any brackets, parts, or accessories that obstruct access to the starter motor mounting bolts. Remove mounting bolts and remove starter. Clean the mounting surface, and install new starter and tighten the mount bolts evenly. Replace wires on starter. Connect battery.
Good luck.

Nov 20, 2011 | 2002 Mercury Mountaineer

1 Answer

Replacing starter 2005 ford focus


starter is located behind the motor under the intake manifold, to replace remove the battery cable & air filter box and remove 2 15mm bolts that go through the bell housing into the starter then get under the car and remove 4 10mm nuts & bolts that attach a plate from intake to the block then remove 1 more 15mm bolt holding starter in and pull it back then nose first down then remove 10mm and 13mm nuts on starter solonoid removing cable and wiggle it out past the half shaft and vualla its out

Jul 08, 2010 | 2005 Ford Focus

1 Answer

Need to replace starter on a 1986 Camaro, but cannot get the old starter past the exhaust pipe.


Removing the starter
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect all wiring from the starter solenoid. Replace each nut as the connector is removed (as thread sizes differ from connector to connector). Note or tag the wiring positions for installation.
  4. Remove the bracket from the starter and the two mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.
  5. Remove the front bracket bolt or nut. Lower the starter front end first, and then remove the unit from the car.
These are the steps for removing the starter on the Camaro. Did you remove the bracket? Hope this helped and best wishes.

Aug 01, 2009 | 1986 Chevrolet Camaro

1 Answer

94 toyota carolla starter clicks eventualy starts


You have two options: replace the starter (easiest, but most expensive), or replace the contacts (cheaper, but more work involved).
In any case, you have to remove the starter. Disconnect the battery BEFORE you start. Locate the starter and remove the wires going to it. The starter is held onto the transmission with 2 large bolts. Remove both, and slide the starter out.

If you want to change the contacts, observe the starter, locate a metal plate held on with 3 bolts. Remove the bolts and the plate. You will now see a plunger, and 2 copper colored contacts. Those are what needs to be replaced. Changing the contacts is easy, just do one at a time, and ensure that all insulators are installed properly on reassembly.

Jan 13, 2009 | 1994 Toyota Corolla

1 Answer

Replacing a starter on a 1997 Dodge Intrepid


No, you can access the starter from the bottom of the engine without having to remove anything else. I replaced the starter on my 94 3.3 myself without having to remove anything else. Good Luck!!!!!

-Matthew

Nov 11, 2008 | 1997 Dodge Intrepid

Not finding what you are looking for?
1998 GMC Sierra Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...