Question about 1986 Chevrolet Camaro

1 Answer

Blinkers Hazards work perfectly fine but blinkers don't please help!!!!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

You should try replacing the turn signal relay, I think its located in the fuse panel.

Posted on May 04, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: my hazards work but my blinkers dont?

does the indicater light just stay on if it does you need a new turn signal flasher.

Posted on Mar 26, 2009

Molson02536
  • 3854 Answers

SOURCE: 97 Chevy truck blinkers not working but hazards do

Try replacing the Flasher first before spending to much money for a possible simple fix. If it's not your flasher then it could be the turn signal leaver.
Ok, this may seem stupid, but that's what they did to the blazer. They set the flasher near the middle and under the center console behind the radio.


It's to the left of the radio right behind the dash. The hazard flasher and the turn signal flasher are side by side.  It right next to the Cig lighter behind the panel. They do mark the turn signal from the hazard flasher on the plastic behind them. Turn is on the right.

Good luck and hope this helps.

Posted on May 02, 2009

VREGG
  • 41 Answers

SOURCE: Blinkers stay solid and dont flash, Hazards work fine.

CHECK GROUND ON TAIL LIGHT HOUSING.

Posted on May 08, 2009

hepcars
  • 1249 Answers

SOURCE: The two brake lights will

The brake light switch is working the third brake light OK? It is odd that both brake light bulbs could be defective at the same time...the hazard turn and brake light bulbs are 2 stage lights...your best check would be to replace one side tail light bulb, and re-check brake light function...these bulbs are multi functional...the brake switch located behind the brake pedal must be OK for the third brake light to remain functioning...

Posted on Dec 09, 2010

jturcotte
  • 8531 Answers

SOURCE: 1999 chevy pickup, no bed brake lights. 3rd cab

Hi, the likely problem is your VEH STOP fuse. in the engine compartment fuse box. Please let me know if you have questions and thanks for using FixYa.


jturcotte_626.gif

Posted on Dec 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Acura 1998 RL blinkers and hazards not working? Replaced Blinker hazard unit under dashboard in fuse box. Still no blinkers and hazards. All other lights work fine.


Have you checked to see if your fuses are good ? If they are, you may want to check power at the switch and then at the relay. Might have a pinched wiring somewhere.

Dec 23, 2016 | 1998 Acura RL

1 Answer

How can i fix the problem blinkers & hazards don't work


If both the blinkers and hazards are not working, check the fuse block for a blown fuse. Also see if your running and brake lights come on. If they do, and there is no blown fuse, try replacing the flasher unit, usually located either near the fuse block or in the glove box area.

Jun 02, 2015 | 1984 Nissan Sentra XE

1 Answer

2001 4 Runner blinker problem


The hazards use a separate relay. listen for signal relay clicking to locate the correct relay. Consult your owners manual for fuse and relay layout.

May 26, 2017 | Toyota 4Runner Cars & Trucks

1 Answer

Hazards dont work but blinkers do


Blinkers and hazards normally work on the same fuse. Sounds like the hazard switch has a problem.Get the hazard switch out and bridge the two connector wires to the switch. If the hazards then work the problem is in the switch.If it don't work you may have a problem in the wiring between the switch and the flasher relay.

May 05, 2013 | 2003 Ford F150 Regular Cab

1 Answer

HAVE RPLACED BULBS AND BRAKE SWITCH AND HAZARDS WORK FINE AND BLINKERS WORK TOO STILL NO BRAKE LIGHTS


check the bulbs again make sure the brake and signal light bulb has two filaments in it, the parking lights ony has one filament

May 21, 2009 | 1999 Ford Taurus

1 Answer

No blinkers/hazards and brake lights won't go off


Did you check the blinkers relay? Tray to get one used at a junk yard or local Autozone and make sure you save the receipt. Install and test.

Feb 22, 2009 | 1996 Volkswagen Jetta

1 Answer

Blinkers and Hazards Stopped working


Signal flasher in fuse panel black and square the one on the right is signal

Jan 26, 2009 | 1998 Dodge Neon

1 Answer

1992 honda accord LX Blinkers


check the hazard switch ive seen them stick or wear out and nothing works. good luck also look for a bulb with only one prong on the end of the bulb it will short the dash lights to keep signal on

Sep 14, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...