Question about 1993 Lincoln Town Car

1 Answer

Cant find the ignition module - 1993 Lincoln Town Car

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

It should be on the drivers side fender near the brake booster and hood hinge

Posted on Jun 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Still no spark coils are good could it be crank position censor and where is ignition module

Yes bad crank sensor will cause no spark. Not all cars have ignition modules so ignitors may take place of them. Check your shop manual for full ignition information.

Jan 20, 2015 | Cars & Trucks

1 Answer

Electrical starting problem, 1988n ford f150 4.9 ltr. I keep getting secondary Ignition. I brunt one starter out already changed it & the starter relay switch , checked ignition switch [o.k], checked...

use ohm meter to check ground to pos cable to starter If 000 check for ground wire on starter it should go to starter bolt. voltage reg stuck open Unplug ignition module check battery if still sparking not module.

Dec 29, 2013 | 1988 Ford F 150

1 Answer

Ignition module

It is mounted in the rear, here is a picture of the part. Autozone can test your Ignition Modules be test yours

Apr 15, 2013 | 1997 Mercury Grand Marquis

1 Answer

1985 corvette key stuck in ignition so cant change it out

You can remove the ignition module as a whole and Dis-Assemble it to remove the tumblers and get the key back that way. If your replacing the Ignition set anyway once you get the module removed you can install the new on and toss the old one. You can have the doors and trunk re-keyed by a locksmith to match the new key. Make sure you remove any key chain you have attached to the ignition key that is stuck and follow the removal steps for the ignition module. Should be fine.

Jul 12, 2010 | 1985 Chevrolet Corvette

1 Answer

Installed new ignition module and now my I cant

The ignition key controls many things including electrical & electronic. It also finally locks the steeringwheel by a pin/bolt sliding into the slot for keeping it locked when parked. Maybe the replaced model is different but only a trained repairman will be able to repair it.............sodeep

Sep 25, 2009 | 1995 Pontiac Grand Prix

1 Answer

Tacho N/W changed ignition from MSD to ign.

its usally the green wire might go to the coil not sure on that model

Jun 05, 2009 | 2008 Subaru Impreza

1 Answer

Where is the ignition module located on the 1996 ford contour?

tragik nc: In looking this car up in both the 4 and 6 cyl configurations, Ford said that the ignition control module is no longer a separate component. It is actually integrated into the PCM (power control module)
This is located in the right rear corner of the engine compartment behind the power steering reservoir.
Good Luck, mybunkey>>>>>>>>>>>>>>>>>

Apr 20, 2009 | 1996 Ford Contour

Not finding what you are looking for?
1993 Lincoln Town Car Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

81400 Answers

gerry bissi

Level 3 Expert

4376 Answers


Level 3 Expert

5687 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides