Question about 2001 Pontiac Aztek

Open Question

How to replace crank sensor

Where is the crankshaft sensor locatoin

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank position sensor on a 97 Hyundai elantra


Here's a link to what your crankshaft sensor looks like. Duralast Crankshaft Position Sensor SU4127 ReadReviews onDuralast SU4127 The Crankshaft Position Sensoris located: Under hood, center, upper engine area, mounted in front passenger side of engine block.Here's another link on replacing your sensor.
Repair Guides Electronic Engine Controls Crankshaft Position ckp Sensor...

Sep 28, 2016 | Hyundai Cars & Trucks

1 Answer

Need to know the location of both crankshaft position sensor on 2008 Chevrolet hhr plz thx


Only has one crankshaft position sensor ,an cam sensors . To change the crank sensor u would have to pull the starter ,located above starter .
Camshaft Position Sensor Replacement - Intake Camshaft Position Sensor Replacement - Exhaust
After a crank sensor replacement a
Crankshaft Position System Variation Learn has to be done !
Important: The crankshaft position (CKP) system variation learn procedure is required when the following service procedures have been performed, regardless of whether DTC P0315 is set:
?€¢
Engine replacement


?€¢
Engine control module (ECM) replacement


?€¢
Crankshaft damper replacement


?€¢
Crankshaft replacement


?€¢
CKP sensor replacement


?€¢
Any engine repairs which disturb the crankshaft to CKP sensor relationship

Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
?€¢
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.


?€¢
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.


?€¢
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.

Apr 04, 2016 | Chevrolet Cars & Trucks

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

1 Answer

Where is the crank sensor located on a 06 toyota highlander


images for Where is the crank sensor located on a 06 .

How To Install Replace Crankshaft Position Sensor Toyota ...

? 6:58
https://www.youtube.com/watch?v=M6zU6jh8pNc
Jan 24, 2011 - Uploaded by 1A Auto Parts
How To Install Replace Crankshaft Position Sensor ToyotaCamry 3.0L V6 1AAuto.com ... the crankshaft position sensoron a 1994 Toyota Camry 3.0L V6. ..... 2002-2006 LEXUS ES300 ES330 TOYOTA CAMRY KNOCK ...

Dec 05, 2015 | Toyota Cars & Trucks

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

2 Answers

97 buick lesabre problems


Will it only crank with the starter shorted, and not with the key?

Jul 06, 2014 | 1997 Buick LeSabre

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

Not finding what you are looking for?
2001 Pontiac Aztek Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...