Question about Hyundai Motor 2002 Elantra
Trying to replace horn on 2002 Hyundai elantra can not find horn any where.
Why do you have to find an OEM horn? There are tons of horns that work just as well if not better. I bought my wife a used Kia Sorento a few years back and in two weeks the horn went out I went to the parts store got two new horns a high and a low tone horn cut off the original horn plugs and put crimp on connectors and these horns are way better sounding and a lot louder than the original one. Simple job.. You'll love the results and price about 20 dollars. Dealership order I couldn't even begin to think what they would charge and I could tell you I wouldn't pay it. You can find them but they will be on order.
Posted on Mar 24, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I have done one on 03 if its the same inside of trunk there are several retainers for the interior liner remove these and pull liner back there are 2 or 3 nuts behind that panel once removed lense will come out it comes out kind of hard but it does come out then you just twist the socket out of lense to get to bulb
Posted on May 21, 2009
you might need to get a prybar or something such long, and try to pry it off the belt, it should go easy right away. It is a spring-inside assembly, and won't brake. There also could be a 3/4 hole in it, look from a side. It's for middle size ratched, it can be used to loosen the tensioner from serp. belt.
Posted on Jul 08, 2009
The adjustment screws/nuts should be located either on the top of the headlamp assembly,
behind the headlamp assembly, or near the frame rail by the radiator
You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well
Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)
For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.
For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
Posted on Oct 06, 2009
Then 1, bulbs are burned out
OR 2, the wiring is faulty.
Posted on Nov 04, 2009
Testimonial: "thanx for the solution. took the car to a repair shop and was told that the wiring was faulty. had the car rewired."
First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.
Posted on Feb 07, 2010
Tips for a great answer:
Jan 04, 2016 | Hyundai Cars & Trucks
Dec 29, 2015 | Hyundai Motor 2003 Elantra
Mar 07, 2010 | 1997 Hyundai Elantra
Feb 02, 2010 | 2001 Hyundai Elantra
Jul 08, 2009 | Hyundai Motor 2002 Elantra
Feb 24, 2009 | Hyundai Motor 2003 Elantra
Dec 11, 2008 | 2006 Hyundai Elantra
Oct 07, 2008 | Hyundai Motor 2002 Elantra
Jul 16, 2008 | Hyundai Motor 2002 Elantra
174 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: