Question about 2005 Fiat Panda

Open Question

Install pcv valve

Where is pcv valve?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcv valve 2006 ford five hundred


It is under the throttle body area and it is hard to get to unless you are doing the plugs and have it out of the way. My Ford dealer quoted $166 to change the plugs P&L. I did them myself. Look up your PVC valve on rockauto.com to see what it looks like.
1. Remove the 4 transaxle roll restrictor brace bolts.
o To install, clean the bolts using a wire brush, apply new threadlocker to the threads and tighten to 55 Nm (41 lb-ft) .
2. Remove the bolt and the transaxle roll restrictor brace.
o To install, clean the bolts using a wire brush, apply new threadlocker to the threads and tighten to 48 Nm (35 lb-ft) .
3. Disconnect the positive crankcase ventilation (PCV) valve tube from the PCV valve.
4. If equipped, disconnect the PCV valve electrical connector.
5. CAUTION: A new PCV valve must be installed if removed from the cam cover. Damage will occur to the locking mechanism on the PCV valve. Rotate the PCV valve counterclockwise to remove from the valve cover.
6. To install, reverse the removal procedure

Jul 14, 2016 | 2006 Ford Five Hundred

1 Answer

Where is the pcv valve on a 2008 Lincoln mkz


It's located in the valve cover closest to the fire wall .
Rotate counterclockwise and remove the PCV valve from the valve cover.
  • Discard the PCV valve.
  • For installation, make sure the PCV valve electrical connector is pointing in the correct position to allow the wiring harness to be connected. Incorrect installation would require removal and replacement of the valve.

Dec 22, 2015 | Lincoln Cars & Trucks

3 Answers

How to change the PCV valve on a Avalon 2002? Where is it and do I have to remove anything first?....Thanks Novice


travisgunter_1.gif\
The valve just pulls right out of the hose that its in. No tools or removal of stuff necessary.

May 10, 2011 | 2002 Toyota Avalon

1 Answer

How do you get the pcv valve out of the valve cover


Usually you grasp it an pull it out.

Positive Crankcase Ventilation (PCV) Valve Removal & Installation To Remove:
PCV Valve location (3.3L & 3.8L engines shown, 2.4L similar) chry-04-33-829.gif

  1. Disconnect the vacuum hose from the positive crankcase ventilation (PVC) valve.
  2. Remove the positive crankcase ventilation valve from the valve cover.
To Install:
  1. Install the positive crankcase ventilation valve in the valve cover.
  2. Connect the vacuum hose to the positive crankcase ventilation valve.
prev.gif next.gif

Jan 16, 2011 | 2006 Dodge Grand Caravan

1 Answer

Changing pcv valve in 97 chevy lumina


PCV VALVE LOCATED IN THE FRONT VALVE COVER.JUST PULL PCV VALVE OUT VALVE COVER. THEN YOU PULL PCV OUT OF THE END OF HOSE THEN INSTALL THE NEW ONE. FOR THE 3.8 ENGINE REMOVE THE TOP FUEL INJECTOR COVER.DISCONNECT THE ELECTRICAL CONNECTOR FROM MAP SENSOR AND UNCLIP THE MAP SENSOR FROM THE PCV VALVE ACCESS COVER AND ROTATE IT COUNTERCLOCKWISE TO REMOVE IT.TO REPLACE THE VALVE PULL THE PCV AND O RING ASSEMBLY FROM THE INTAKE MANIFOLD NOTING ITS INSTALLED POSITION AND DIRECTION. MAKE SURE WHEN YOU BUY NEW PCV VALVE TAKE OLD PCV VALVE WITH YOU SO YOU WILL GET THE RIGHT ONE.THAT WILL SAVE YOU TIME AND FUEL.

Dec 26, 2010 | 1997 Chevrolet Lumina

1 Answer

Where would the pvc value be on a 300 chrysler 2006? also where would the spark plugs be located?


Positive Crankcase Ventilation (PVC) Valve Removal & Installation 5.7L Engine To Remove:
    1.The PCV valve is mounted into the top/right side of the intake manifold.

    2.The PCV valve is sealed to the intake manifold with two O-rings.

    3.Free the PCV valve by rotating counter-clockwise 90 degrees until the locating tabs align with the openings on the manifold.

    4.Remove the PCV valve by pulling straight up from intake manifold and clearing the tabs.

    5.Check the condition of two valve O-rings.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Inspect the PCV valve O-rings. Replace if suspect.
  3. Apply engine oil to the two O-rings.
  4. Place the PCV valve into intake manifold.
  5. Rotate the valve 90 degrees clockwise for installation.
6.1L Engine To Remove:
  1. The PCV valve is threaded into the right-front corner of the intake manifold.
  2. Remove the rubber hose from the PCV valve.
  3. Unscrew the PCV valve from the intake manifold.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Check the condition of the PCV valve O-ring. Replace if suspect.
  3. Check the condition of the PCV valve threads and clean if necessary.
  4. Apply engine oil to the O-ring.
  5. Install the PCV valve into intake manifold.
  6. Install the rubber hose to the PCV valve.
prev.gif next.gif
The spark plugs should lead to the coil pack via a spark plug wire but may be hidden by a plastic cover.

The following details the ignition coil changing on the Chrysler 300:

2.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
  1. Install the ignition coil.
  2. Tighten the fasteners to 55 in-lb (6.2 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
3.5L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil. NOTE: Loosen the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when loosening the fasteners.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
NOTE: Tighten the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when installing the coil.
  1. Install the ignition coil.
  2. Tighten the fasteners to 60 in-lb (6.7 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
5.7L Engine (2005) To Remove:
NOTE: Carefully note the position of each spark plug cable before disconnecting them so they can be installed in their original positions to prevent misfire.
NOTE: The throttle body intake air duct or intake air box may need to be removed to gain access to certain ignition coils.
  1. Disconnect the electrical connector from the ignition coil.
  2. Remove the secondary ignition cable from the coil.
  3. Use compressed air to clear the area around the ignition coil.
  4. Remove the two fasteners securing the ignition coil. Bolts are retained to coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Clean area around spark plug and coil mounting area with compressed air.
  2. Install the ignition coil.
  3. Tighten the fasteners to 105 in-lb (12 Nm).
  4. Connect the electrical connector to the ignition coil.
  5. Connect the secondary ignition cable to the coil.
  6. Install the air duct or air box if removed.
Ignition coil mounting bolts (5.7L & 6.1L engines) chry-02-57-263.gif

5.7L (2006) & 6.1L Engine To Remove:
NOTE: Each ignition coil, mounted on the valve cover, fires two spark plugs at each cylinder.
  1. Disconnect the negative battery cable.
  2. Use compressed air to clear the area around the ignition coil and spark plug.
  3. Disconnect the electrical connector from the ignition coil.
  4. Remove the two fasteners securing the ignition coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Install the ignition coil.
  2. Tighten the fasteners to 105 in-lb (12 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Connect the negative battery cable.
prev.gif next.gif

Sep 24, 2010 | 2005 Chrysler 300

1 Answer

How do you change the pvc valve


Not sure on your engine so heres both types. :-) Hope it helps. Cobra
Positive Crankcase Ventilation (PCV) Valve — 3.0L (2V) Removal and Installation
  1. Disconnect the positive crankcase ventilation (PCV) valve tube quick-connect from the PCV valve.
e8e1fc3.jpg
CAUTION: A new PCV valve must be installed if removed from the cam cover. Damage will occur to the locking mechanism on the PCV valve.
Remove the PCV valve.
  • Disconnect the PCV valve electrical connector.
  • Rotate to release and remove the PCV valve.
cb7856a.jpg


Positive Crankcase Ventilation (PCV) Valve — 3.0L (4V) Removal and Installation
  1. Disconnect the positive crankcase ventilation (PCV) valve tube from the PCV valve
0f6f63a.jpg

  • CAUTION: A new PCV valve must be installed if removed from the cam cover. Damage will occur to the locking mechanism on the PCV valve.
    Rotate to release and remove the PCV valve.

  • 26db756.jpg

  • Jun 13, 2010 | 2005 Ford Taurus

    2 Answers

    How to replace pvc valve


    SECTION 303-08: Engine Emission Control 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Positive Crankcase Ventilation (PCV) Valve —2.0L Zetec Removal and Installation
    1. Remove the PCV valve (6A666).
      • Remove the crankcase ventilation hose (6853) from the PCV valve (6A666).
      • Remove the PCV valve from the grommet.
    62777e1.gif

    Dec 31, 2009 | 2001 Ford Escape

    5 Answers

    How do I remove the pcv valve from a 3.8 liter engine in a 2005 dodge grand caravan? I cannot pull it out.


    1. BUY THE NEW PCV VALVE FROM THE DEALER. part #4648973AC (I paid $9.95 in the Detroit area). 2. PCV valve is located on top of 'rear' valve cover. There is a black rubber pipe connecting the PCV to the upper intake manifold. The rubber pipe is like an inverted 'U' shape. 3. To remove the rubber pipe, you will need to squeeze the band clamps. Remove the upper end first. You will then be able to rotate the lower end clockwise, if necessary, to get enough clearance to use pliers to squeeze the band clamp. Remove the pipe. 4. You should be able to see the small chrome pipe on the end of the PCV valve. However, the PCV valve is completely surrounded by a plastic collar/shroud, part of the plastic valve cover. So, the only part of the PCV that is accessible is the small chrome pipe. 5. THIS IS WHY YOU NEED TO BY THE NEW PART FIRST. I needed to clamp onto the end of the PCV pipe with VISE-GRIPS. This will crush the end of the pipe. You will hold the vise grips in a horizontal fashion, towards your right, in your right hand. 6. Rocking the pipe, while carefully levering the vise grips on top of the plastic collar, you will walk the PCV valve up, and out. BE PATIENT. You do not want to crack the valve cover! 7. The rubber grommet should come out with the PCV metal valve. If not, you will need to pull it out (needle nose pliers?). 8. Install the new PCV valve. I used a film of white lithium spray to help the insertion. Note, there is a groove molded into the rubber grommet that must snap into place. I used a 5/8" deepwell socket as a 'pusher', to ease the PCV valve into place (just push, do not hammer). You should be able to feel it positively snap into place inside the plastic collar, otherwise it is not properly installed and will not seal. If properly installed, you will not be able to pull it out by hand. 9. Install the PCV rubber pipe. Slide the clamps towards the middle of the pipe, fit the pipe over PCVvalve. Be sure it is seated all the way to the bottom of the plastic collar. Squeeze the clamp and work down to the bottom of the pipe, then release. Repeat for the upper end of the pipe and spring clamp. 10. Have a cold one. You earned it.

    Jun 27, 2009 | 2005 Dodge Grand Caravan

    3 Answers

    Where can I find the pcv valve location


    please rate as fixed if this helps.

    4 cylinder

    SECTION 303-08: Engine Emission Control 2003 Escape Workshop Manual
    REMOVAL AND INSTALLATION Positive Crankcase Ventilation (PCV) Valve —2.0L Zetec Removal and Installation
    1. Remove the PCV valve.
      • Remove the crankcase ventilation hose from the PCV valve.
      • Remove the PCV valve from the grommet by turning the valve counter-clockwise
    f21fec7.gif
    ------------------------------

    Apr 12, 2009 | 2005 Ford Escape

    Not finding what you are looking for?
    2005 Fiat Panda Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Fiat Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Fiat Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...