Question about Porsche 928
928 s4 Porsche 300 kw 32 valve V8 key cutting problem. No key cutters in New Zealand can do it. We have found places that have blank keys but no machinery to cut the angle.
Find the Porsche dealer service centre / parts department as they will have replacement keys and probably a key cutting and programming machine.
Posted on Mar 24, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
this is the procedure to remove the ignition barrel:
Remove the steering column surround and you should see a black round thing on the left hand side, this is the ignition switch. Remove this and you will see there is one screw holding the ignition barrel on, remove and you then need to insert your key and turn it to the ACC position. you should now be able to withdraw the barrel using the key but take care not to snap the key off in the barrel.
Please don't forget to rate or accept the solution as fixya.
Posted on Jun 15, 2008
SOURCE: reprogramming remote and key
if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.
Posted on Jun 21, 2009
did the lock smith cut key with resister in in maybee not gotta go to dealer get one cut then put old key in start car then turn of remove key put new key in turn on till security light goes out then start car
Posted on Aug 29, 2009
Tips for a great answer:
Jul 18, 2014 | 2001 Porsche Boxster
Nov 24, 2012 | 2000 Porsche Boxster
Jun 09, 2017 | 2004 Porsche Cayenne
May 29, 2011 | 1999 Porsche Boxster
Aug 20, 2009 | Porsche Boxster Cars & Trucks
Apr 07, 2009 | 1999 Porsche 911 Carrera
162 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: