Question about 2000 Chrysler Sebring

1 Answer

Throttle cable the throttle body cable is loose how do I tighten it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 154 Answers

They sell new crimper pieces at auto stores,recrimp the cable tighter

Posted on Mar 23, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the fuel injector for a 2008 chrysler pt cruiser?


To remove a fuel injector or injectors you must remove the fuel supply rail that sits over them. Here is how you do that for both engine options, Turbo and non Turbo..

Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRB® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

How to replace the fuel injector on a 2008 chrysler pt cruiser


Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRB® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

Throttle cable on a 95 grand am has recently come lose, looking for tips on tightening it if possible. I can't see anything wrong with the cable itself so not sure if I should replace or just tighten


Most throttle cable have a tensioner nearby the throttle body. Run your finger down the line and look for a bulk in the line thats either open with no cover, or covered. If its covered, and easily removable, remover it and there should be two nuts there. Tighten the back nut, i believe.

Jul 10, 2013 | Cars & Trucks

1 Answer

1995 oldsmobile achieva 2,3L how do I adjust the throttle cable.


You can't make any adjustments, the idle speed is controlled automatically by a computer called the ECM.

Apr 22, 2012 | Oldsmobile Achieva Cars & Trucks

1 Answer

How to replace the throttle cable on 1996 sinfire


InstructionsThings You'll Need
  • Mechanic's toolset, including a full socket set, wrenches and screwdrivers
  • Torque wrench
  • Clean shop cloths
  • Replacement gasket
    • 1

      Take out the air cleaner resonator. Disconnect the harness connectors for both the idle air control and the throttle position sensor. Label and then remove all the vacuum hoses from the throttle body.

    • 2

      Remove the bracket and the cables for the accelerator control from the throttle body. Loosen and remove the throttle body fasteners.

    • 3

      Lift the throttle body off the manifold. Remove the throttle body gasket and inspect it carefully. Replace the gasket as needed or re-install the old gasket to the throttle body after cleaning all the mating surfaces thoroughly.

    • 4

      Set the throttle body on the manifold and finger-tighten the fasteners. Torque the bolts to 89 inch pounds.

    • 5

      Install the cables and bracket for the accelerator cable, then reconnect the vacuum hoses. Reconnect the harness connectors for the throttle position sensor and the and idle air control valve, then replace the air cleaner resonator.

    • 6

      Depress the accelerator pedal to test its movement and to assure that there is no binding. Press the pedal to the floor one time then release it. Make the necessary adjustments.

Jan 11, 2012 | 1996 Pontiac Sunfire

1 Answer

The throttle cable is loose and I need to know how to tighten it. 2002 Mitsubishi Eclipse - 4 cyclinder


you will need to tighten the adjusting cable, here is a website that tells the removal, it should help Tim:

http://www.ehow.com/how_4590676_replace-throttle-body-mitsubishi-eclipse.html

Oct 20, 2010 | 2001 Mitsubishi Eclipse

1 Answer

Where is the carb on a jeep grand cherokee 1993 4.0 liter


There is no carburetor on any of the 6 cylinder or 8 cylinder Jeep Grand Cherokees. They have Fuel Injection and a throttle body which looks like a carburetor scaled down.

---
Instructions on how to remove and replace the throttle body follow:

Throttle Body REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hoses from upper bonnet, unfasten the retaining clips and remove the upper bonnet assembly.
  3. Remove the lower bonnet retaining bolts and lower bonnet.
  4. Remove the throttle cable and the return spring.
  5. Disengage the wire harness connector from the injector.
  6. Disengage the wire harness connector from the WOT switch, ISA motor and TPS.
  7. Disconnect the fuel supply and return lines from the throttle body.
  8. Tag and disengage the vacuum hoses from the throttle body assembly.
  9. Disengage the potentiometer wire connector.
  10. Loosen throttle body retaining bolts and remove throttle body assembly from the intake manifold. To install:
  11. Clean the intake manifold and throttle body mating surfaces of old gasket material.
  12. Install a new gasket and the throttle body assembly. Tighten the mounting bolts to 16 ft. lbs. (21 Nm).
  13. Engage the potentiometer wire connector.
  14. Engage the vacuum hoses to the throttle body.
  15. Engage the fuel lines to the throttle body.
  16. Engage the WOT switch, ISA motor, TPS, and injector electrical connections.
  17. Install the return spring and throttle cable.
  18. Install the lower bonnet and fasten the retainers.
  19. Install the upper bonnet assembly, retaining clips and vacuum hoses.
  20. Connect the negative battery cable.
  21. Start the vehicle and check for fuel leaks. Fig. 1: Exploded view of the throttle body and related components 86745g41.gif
prev.gif next.gif

Aug 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Replace starter


REMOVAL & INSTALLATION

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the terminal nuts, washers, and electrical leads from the starter motor.
  4. Remove the passenger side catalytic converter.
  5. Remove the passenger side engine mount nuts, and lower the vehicle.
  6. Disconnect the resonance chamber-to-throttle body ducts.
    1. Detach the electrical connector for the Mass Air Flow (MAF) and the Intake Air Temperature (IAT) sensors.
    2. Disconnect the resonance chamber air intake hose from the air cleaner housing and MAF sensor.
    3. Remove the (IAC) inlet hose and the intake plenum air inlet hoses.
    4. Detach the electrical connector from the switchover valve and the remaining vacuum connections.

  7. Install the engine support fixture J28467-A with adapters J28467-450 or equivalents and raise the passenger side of the engine.
NOTE Passenger side of the engine must be raised approximately 1.5 inches (38 mm).
  1. Raise and safely support the vehicle securely on jackstands.
  2. Remove the engine mount from the engine mount bracket and cradle.
  3. Remove the engine mount bracket bolts and reposition the bracket.
  4. Remove the starter motor from the vehicle.
To install:
  1. Install the starter motor to the vehicle and tighten the bolts to 44 ft. lbs. (60 Nm).
  2. Position the engine mount bracket and install the bolts. Tighten to 30 ft. lbs. (40 Nm).
  3. Install the engine mount to the engine mount bracket and cradle. Partially lower the vehicle.
  4. Lower the engine. Have an assistant guide the engine mount into place while lowering the engine. The engine mount locator tab must engage the slot in the cradle.
  5. Reinstall the resonance chamber-to-throttle body ducts.
  6. Raise the vehicle.
  7. Install the passenger side engine mount nuts. Tighten the upper nut to 30 ft. lbs. (40 Nm). Tighten the lower nut to 41 ft. lbs. (55 Nm).
  8. Install the passenger side catalytic converter.
  9. Plug in the electrical leads, install the washers, and terminal nuts to the starter motor. Tighten the battery cable terminal nut to 115 inch lbs. (13 Nm). And the solenoid terminal nut to 35 inch lbs. (4 Nm).
  10. Lower the vehicle.
  11. Connect the negative battery cable.

4.6L Engine
  1. Disconnect the negative battery cable.
  2. Disconnect the positive battery cable.
NOTE In order to get to the starter assembly the intake manifold must be removed. Refer to the procedure for removing the intake manifold.
  1. Reposition the front bank spark plug wires.
  2. Remove the air intake duct from the throttle body.
  3. Detach the electrical connectors for the intake manifold, Throttle Position (TP) sensor, and Idle Speed Control (ISC) motor, Evaporative Emission (EVAP) Control solenoid and Cruise Control Servo.
  4. Disconnect the vacuum hoses at the brake vacuum booster, fuel pipe bundle and to the body.
  5. Disconnect the PCV hoses at the intake manifold.
  6. Unhook the accelerator cable at the throttle body and position it out of the way.
  7. Relieve the fuel system pressure. Disconnect the fuel pipe quick connects at the fuel pipe bundle in the engine compartment.
  8. Remove the EVAP solenoid bracket at the rear (or right) cam cover.
  9. Reposition the transaxle range control cable away from the cruise control servo.
  10. Disconnect the coolant hoses at the throttle body and to the coolant reservoir and plug the hoses. Wrap a shop towel around the hoses when disconnecting to avoid spillage.
  11. Remove the four intake manifold bolts and lift the intake manifold with the throttle body out of the engine compartment.
  12. Unbolt the solenoid 'S' terminal nut and battery cable nut. Remove the starter motor mounting bolts, and lift the starter motor out of the manifold cavity.
To install:

NOTE Before installing the starter motor to the engine, tighten inner nuts on the solenoid terminals to be sure they are secure in the cap. Tighten the inner nuts on the battery terminal and motor terminal to 71 inch lbs. (8 Nm). If the nuts are not properly tightened, the starter may fail later due to the terminal or cap damage.
  1. Install the solenoid switch lead, and tighten the nut to 22 inch lbs. (2.5 Nm).
  2. Install the battery cable nut and tighten to 71 inch lbs. (8 Nm).
  3. Install the starter motor and tighten the mounting bolts to 22 ft. lbs. (30 Nm).
  4. Install the intake manifold with the throttle body onto the engine and install the four bolts. The four intake manifold bolts must be tightend in a specific sequence to 71 inch lbs. (8 Nm), then an additional 120°.
  5. Connect the coolant hoses at the throttle body and at the coolant reservoir. Add coolant as needed.
  6. Position the transaxle range control cable to the cruise control bracket.
  7. Fasten the EVAP solenoid bracket to the rear cam cover.
  8. Reconnect the fuel pipes quick connects at the fuel pipe bundle in the engine compartment.
  9. Hook the accelerator cable up at the throttle body.
  10. Connect the vacuum hoses at the brake vacuum booster, fuel pipe bundle and to the body. Install the PCV hose at the intake manifold.
  11. Install the electrical connectors for the intake manifold, the TP sensor ISC motor, EVAP solenoid and the cruise control servo.
  12. Install the air intake duct to the throttle body.
  13. Reposition the front bank spark plug wires.
  14. Connect the negative battery cable.
  15. Connect the positive battery cable.

4.5L and 4.9L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the starter motor shield.
  4. Remove the exhaust front and rear pipe assembly.
  5. Remove the flexplate inspection cover.
  6. Disconnect the solenoid 'S' terminal nut and battery cable nut.
  7. Unbolt the starter motor mounting bolts, and remove the starter motor.
e2d3282.jpg
Fig. Typical starter mounting on early models

b5066a8.jpg
Fig. Later model starter location and mounting on the 4.9L engine


a697aa3.jpg
Fig. Starter mounting on 4.5L engine with a starter shield


To install:
  1. Install the starter motor, and tighten to 32 ft. lbs. (43 Nm).
  2. Install the solenoid 'S' terminal nut. Tighten the nut to 35 inch lbs. (4 Nm).
  3. Install the battery cable nut and tighten to 12 ft. lbs. (15 Nm).
  4. Install the flexplate inspection cover, the front and rear exhaust pipe assembly and the starter motor shield.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope trhis help (remember comment and rated this).

Apr 08, 2010 | 1992 Cadillac DeVille

1 Answer

Need to replace a idle air control valve on a 1999 300M Chrysler


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the IAC electrical connector.
  3. Remove the IAC mounting screws.
  4. Remove the IAC.



da3669e.gif

To install:
  1. Install the IAC to the throttle body.
  2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
  3. Attach electrical connector to the IAC.
  4. Connect the negative battery cable.
  1. Disconnect electrical connector from IAC motor.
  2. Disconnect air plenum (where applicable).
  3. Remove two mounting bolts (screws).
  4. Remove IAC motor from throttle body.

3ccd55e.gif

To install:
  1. Install IAC motor to throttle body.
  2. Install and tighten two mounting bolts (screws) to 60 inch lbs. (7 Nm) torque.
  3. Install electrical connector.
  4. Connect air plenum (where applicable).

Mar 06, 2010 | 1999 Chrysler 300M

1 Answer

Loose gas pedal, i need to push accelerator farther in


the gas pedal is connected by a cable that goes to the throttle body or carburetor on the engine. there should be a nut that holds the cable end in place where the steel cable comes out of the housing near the throttle body. it sounds like this may be loose or stripped out. you may need to replace the entire throttle cable.

Feb 17, 2010 | 1984 Toyota Xtracab

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...