Question about Mazda MPV

1 Answer

Cranking but not starting

Hold light flashing and security light flashing 2 long 4 short

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

2004 suzuki verona: the transmission starts off in third gear..idle Here's one for you ..... My verona started doing the samething . Checked the code (crankshaft sensor A low voltage) cleared the code , but it came back ...Checked all fuses, all OK.. Started the car , while running pulled the fuse for trans control mod .(drivers side dash panel) Light stop flashing ... Put the fuse back in . No more shift problems ..... Tom Bowman / thomas_bowman@bellsouth.net

Posted on May 21, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: security light flashes

from what i have read, it is design to cut the gas supply so no one can still your car. Mine car wouldn't crank at all with the light blinking. turn the key to the on position and wait 10 minutes. turn it off and try to crank it. it has worked every time on mine. I have also read to cut the LITTLE yellow wire that runs from ignition,but i don't feel comfortable cutting wires even though you can always reattch the wire.

Posted on May 25, 2009

csmock132
  • 4669 Answers

SOURCE: insalled new computer,cranks but wont start

Does it start and die after 1-2 seconds or just cranks and never fires? Did it run before you installed the computer or are you trying to cure a no start problem?

Posted on Jul 12, 2009

elix0411
  • 3530 Answers

SOURCE: my security light in my

Welcome to Fixya

The Passlock "system" causes the security light to blink intermentally. When this occurs, the PassLock security system shuts off the fuel to the car and the car will not start for about 10 minutes. After about 10 minutes, it starts fine. Leave the key to "ON" position for 10 minutes. You will hear clicking noises coming from within the dash after 10 mins. This means you can now start your engine. You might need to replace the passlock sensor to resolved the problem. You may try the alternative key in doing this.

Thank you for using Fixya!

Posted on Jan 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 oldsmobile 88 anti-thef system cause no power to fuel pump?


Is the SECURITY light lit on the insturment cluster ? Does the engine spin with key in start position ?

Vehicle Theft Deterrent (VTD) System Check

Attempt to start the vehicle.
NO - The engine cranks and starts.
Refer to Engine Cranks but Does Not Run in Engine Controls.
2
Note the security indicator while attempting to start the vehicle.
The indicator light is ON and OFF after approximately 5 seconds.
• SECURITY Indicator Always On or Flashing, Engine Does Not Crank
• SECURITY Indicator Always On or Flashing, Engine Starts
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

Engine Cranks But Does Not Run !

Feb 18, 2017 | 1998 Oldsmobile 88

2 Answers

2002 Trailblazer security light on, will not crank, replaced steering column


Did you use the original key and lock cylinder? They are coded for the security system.

Dec 31, 2016 | 2002 Chevrolet TrailBlazer

1 Answer

What could keep my coil from firing ? I have the Ignition control signal and 12v. while cranking over engine at the top primary wiring of coil. Can you help me get spark?


Sounds like the security system is causing your problem. Is the "security" light flashing? If it is, turn the key on, leave the key in the ON position for 10 minutes. The light will stop flashing. Now, turn OFF the key, turn it back to ON, and then crank it. It should start. If the security light starts flashing again, go through the process again until it starts. This is resetting the security system after the battery has died, battery has been changed, radio was changed, instrument cluster was removed and replaced, etc. Hope this works for you.

Mar 29, 2016 | 2001 Chevrolet Silverado 1500

1 Answer

Mazda 6 security light


sounds like key is bad maybe worn out,have you used different key recently

Mar 23, 2014 | 2004 Mazda MPV

1 Answer

Security reset


Depending on the make model and year, did you have a key cut to match the new lock cylinder and the old key chip ?

Jul 06, 2013 | Cars & Trucks

1 Answer

97 sunfire cranks ok but wont start security light on steady


the fuse for the obd2 is usually the cig lighter ,replace fuse and connect tech 2 try reprogram if it connects!

Apr 03, 2013 | Cars & Trucks

1 Answer

Reset security system


To review - the factory VATS security system will not let the engine crank or start if the wrong key is used or there is a problem with the system.
So if the engine was cranking the security system was not at fault.
You may have to get a used shop manual to get the testing procedures for a no start-stall problem.

Feb 25, 2013 | 1999 Chevrolet Cavalier

1 Answer

I turn the key and the security light flashes


leave the key in the ignition, turned to 'run' (just before the crank position) and leave it there for about 15 minutes-the security light will then stop flashing-so NOT turn it off, turn it to crank and start the car. You have a security module that is not seeing the same resistance in the ignition switch as it expects, meaning you will have to either replace the ignition switch (expensive) or bypass the module (easy and inexpensive)-I have done lots of these, requires about 15 cents worth of parts and can be done in 1/2 hour.

Jan 24, 2011 | 2003 Pontiac Grand Am

1 Answer

My 2000 lesabre will start sometimes and wont sometimes. for the last wk it wont start. it has power lights work everything just wont crank whats wrong with it. jf1


Hello: Make sure the battery cables are clean No corrosion, and tight. If the security light is not flashing when you try to start it, the have a helper hold the ignition switch in the start position and you go under the car and hit the starter (not to hard) near the end that goes into the engine, If it starts then you need a starter. If the security light flashes while trying to start you have a pass key problem

Jan 07, 2011 | 2000 Buick LeSabre

1 Answer

Insalled new computer,cranks but wont start


Does it start and die after 1-2 seconds or just cranks and never fires? Did it run before you installed the computer or are you trying to cure a no start problem?

Jul 12, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...