Question about 1996 Nissan Quest

1 Answer

Engine start to faill as soon get warm

When it's been like 20 to 25 min after i start run the engine start to fail

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Have your distributor tested - might be getting hot and fail. Just like an external coil.

Posted on Mar 23, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 vw passat 2.0 tdi starts when cold but after it gets warm stop engine wait five min then want start tell stone cold just changed crank sensor


Need more info, does the coil get hot? Run it and as soon as it stops feel the coil and see if it's hot.

Apr 02, 2015 | 2004 Volkswagen Passat

1 Answer

302 bronco stalls after it warms up and won't start till it cools down


I am guessing its your TFI or Thick Film Ignition module. Usually located on the underside of your distributor, its either grey or black in color and often when it is going bad it acts like this: Usually starts fine, runs ok for about 20 min then engine dies. cranking engine sounds normal but no start. checking spark will have no sparks. Leave hood up and allow to cool (also TFI very hot to the touch) I packed Ice around it once (in a ziplock) that made it run in about 45 min. NOTE: get ready to replace real soon because its on the way to breaking down.

May 09, 2014 | 1987 Ford Bronco

1 Answer

2000 suzuki vitara runs 15 min stalls wont start till cools down


Did they figure out if you are loosing fuel or spark when it fails to start up ? You would need to know which to proceed.

Feb 13, 2014 | Suzuki Grand Vitara Cars & Trucks

1 Answer

I have a 2003 kia sedona van 3.5 liter that jumped time. I reset the timing put a new belt on it and it ran good for 35-45 min. Then it cut off, and wouldn't start back up. It has an OBD2 code for cam...


cam sensor fail can be crank sensor fail engine will run with cam sensor fail but crank it will not fire. also recheck the timing belt settings you fit the timing belt and run engine till warm then recheck the belt adjustment to make sure its in line and at recommended tightness.

Aug 07, 2017 | Cars & Trucks

1 Answer

94 jeep grand cherokee. starts,idle. throw warmup. as soon as I touch the excellerator let up the rpm drop & engine stalls.


Most low idle speed problems on these engines are due to a faulty idle air control valve but since you state the idle will go up and return to idle then i would say it is working properly i think you have a throttle body coking problem ( dirt and grit accumulates around the butterfly valve in the throttlebody ) to fix this simply remove the fresh air hose from the throttlebody and open the throttle all the way up use a clen rag and wipe clean you may use a solvent such as B12 on the rag but dont use too much 1_4_2013_4_54_06_am.jpg

Jan 04, 2013 | 1994 Jeep Grand Cherokee

1 Answer

Truck not starting no problems the night before


need to monitor ipr pressure (injection oil pressure)must reach 500psi
in order to start engine
may have failled o -ring or stc fitting in injection side or possible ipr failure
valve cover right side front icp sensor removed apply 5000psi gage and
crank engine over have someone monitor and report
if this pressure is less then 500 psi it will not start removed gaged
key ignition at run apply shop air min 100 psi and listen at oil fill for gurguling oil sound
if so oil leak in hi pressure oil side

Oct 29, 2010 | 2004 Ford F350

1 Answer

91 mighty max wont start when cold


Next time when cold and it will not start remove a spark plug or two and see if the engines flooded. If so there are two things that come to mind; 1, worn injectors, leaking as engine sits with time causing difficult starts 2: bad oxygen sensor, if failed engines tend to run rich and the ECU may have your injectors pump heavy amounts of fuel to keep from running lean; often times you'll see poor fuel MPG if O2 sensor failed.

I hope this may have assisted you,
Tom

Oct 30, 2009 | 1991 Mitsubishi Mighty Max

Not finding what you are looking for?
1996 Nissan Quest Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...