Question about 2000 Ford Expedition

1 Answer

Crossovers how do I remove the water crossover connection

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Ford Master
  • 1,632 Answers

Remove hose at junction

Posted on Dec 14, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 f150 ford coolant crossover problems 5.4 liter engine

sitting timimg chain on 2000 f150 5,4

Posted on Jan 28, 2009

  • 1608 Answers

SOURCE: is the thermostat on a 2004 ford f150, v8 5.4L

Just follow the upper radiator hose to the thermostat housing.the thermostat is under the housing.Top center of motor.Hope this helps.

Posted on Dec 17, 2009

  • 64 Answers

SOURCE: I have a cracked aluminum coolant crossover. can i

No you cannot. You have to buy the whole intake.

Posted on Dec 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

1 Answer

Having a promblem taking off crossover exhaust pipe on a 2005 Buick rendezvous I tooken off the two front exhaust Then took bottom two bolt . But still fasten to something is there other bolts...


Thermostat? engine cooling?
2 engines, here, LYA adn LY7.
nobody here posts engine, why do that?
so ill post only for 1.
the LA1
here are the steps.
NO FSM Sux huh? nor an alldata.com account, why not that? 15 bucks?


STAT out.
Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 3.4L.

Drain the coolant until the coolant level is below the thermostat. Refer to Cooling System Draining and Filling (Refer To List 1) .

Remove the crossover exhaust pipe. Refer to Exhaust Crossover Pipe Replacement (Refer To List 2) in Engine Exhaust.

Remove the radiator hose from the thermostat housing.

Remove the thermostat housing bolts and clean any sealer from the bolt threads.

Remove the thermostat housing and gasket.
remove STAT
next is crossover page.

Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection (Refer To List 1) in Engine Electrical.

Remove the throttle body air inlet duct.

Drain the coolant from the cooling system. Refer to Cooling System Draining and Filling (Refer To List 2) in Engine Cooling.

Remove the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement (Refer To List 3) in Engine Cooling.

Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



Remove the exhaust crossover heat shield bolts.

Remove the exhaust crossover heat shield.
  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.

end , remove.

now the bypass pipe FWD cars SUCK
  1. Disconnect the left engine mount strut from the engine.
  2. Remove the heater hose from the bypass pipe.
  3. Remove the thermostat bypass pipe to throttle body nut.
  4. Use the J 38185 in order to remove the thermostat bypass pipe hose clamps (1,5).
  5. Remove the thermostat bypass pipe to cylinder head nut (3).
  6. Remove the thermostat bypass pipe bolt (4).
  7. Remove the thermostat bypass pipe hose.
  8. Remove the thermostat bypass pipe.
sigh.....
why not log in to alldata.com
read the page then ask ques tons that are not clear.
and next time post the engine type.
above is just 1 engine.

Jun 18, 2014 | Cars & Trucks

1 Answer

My husband and I are trying to get to our thermostat to change in my 2002 rendezvous, but there is a metal pipe in the way that we can't figure out how to remove. just behind the pipe, is a metal plate...


Hello vocalviixen,

The pipe that you referred to is the exhaust crossover pipe. Below I've included removal and installation instructions.

Also, the procedure for bleeding the coolant system is critical; if you need those instructions please post the question.

REMOVAL PROCEDURE
1. Disconnect the battery ground (negative) cable.
2. Remove the throttle body air inlet duct.
3. Drain the coolant from the cooling system.
4. Remove the inlet radiator hose from the engine.
5. Remove the thermostat bypass pipe.
6. Remove the exhaust crossover heat shield bolts.
7. Remove the exhaust crossover heat shield.
8. Remove the exhaust crossover pipe studs/nuts.
9. Remove the exhaust crossover pipe.
INSTALLATION PROCEDURE
1. Install the exhaust crossover pipe.
2. Install the exhaust crossover pipe studs/nuts.
3. Tighten the exhaust crossover pipe studs/nuts to 18 lb ft.
4. Install the exhaust crossover heat shield.
5. Install the exhaust crossover heat shield bolts.
6. Tighten the exhaust crossover heat shield bolts to 89 lb in.
7. Install the thermostat bypass pipe.
8. Install the inlet radiator hose to the engine.
9. Fill the cooling system with engine coolant.
10. Install the throttle body air inlet duct.
11. Connect the battery ground (negative) cable.


Regards,
netvan

Mar 14, 2011 | 2002 Buick Rendezvous

2 Answers

My cadillac eldorado etc 98 model needs a water pump pulley i can not find it anywhere does it go by any other name it is over heating and a we called a mech friend and he said it was the water pump and...


The water pump should come with a pulley on it or at least transfer over to the new one if it doesn't come with a pulley. Water Pump Removal and Installation All Engines To Remove:
  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
  2. Remove or disconnect the following:
    • Coolant into a suitable container
    • Upper filler panel
    • Air cleaner assembly
    • Secondary AIR injection control valve gm_car_cad_sev_wtr_pmp_belt_shld.gif

    • Oil level indicator tube nut
    • Water pump belt shield fasteners
    • Water pump belt shield gm_car_cad_sev_wtr_pmp_drv_belt.gif

    • Water pump drive belt (D) gm_car_cad_sev_rad_outl_hos.gif

    • Radiator outlet hose from the thermostat housing gm_car_cad_sev_wtr_pmp_and_covr.gif

    • Water pump cover bolts
    • Water pump cover
    • Heater return hose
    gm_car_cad_sev_wtr_pmp_pulr.gif

  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Remove or disconnect the following:
    • Pump from the housing:
      1. Use suitable water pump puller/installer tool (or special service tool J38816-A) to turn the pump clockwise
    • Support plate from the water housing crossover gm_car_cad_sev_wtr_pmp_rem.gif

    • Water pump
    • Seal from the water crossover
  6. Clean the sealing surfaces of the water housing crossover and the pump cover.
  7. Clean and inspect the water pump.
To Install:
  1. Install or connect the following:
    • Seal into the recessed portion of the water crossover
    gm_car_cad_sev_wtr_pmp_crosovr_seal.gif

    NOTE: The notched locking ear must be in the 7 o'clock position.
  2. Index the water pumps locking ears with the tangs in the water crossover.
  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Turn suitable water pump puller/installer tool (or special service tool J38816-A) counterclockwise.
  6. Torque the water pump
    • Torque to: 74 ft. lbs. (100 Nm)
  7. Remove the support plate from the water housing crossover.
  8. Install or connect the following:
    • Water pump cover to the heater return hose
    • Water pump cover to the water housing crossover
    • Water pump cover bolts
      1. Torque to 89 inch. lbs. (10 Nm)
    • Radiator outlet hose to the thermostat housing
    • Water pump drive belt
  9. Place the water pump belt shield in position.
  10. Install or connect the following:
    • Water pump belt shield fasteners
      1. Torque to 89 inch. lbs. (10 Nm)
    • Oil level indicator tube nut
      1. Torque to 89 inch. lbs. (10 Nm)
    • Secondary AIR injection control valve
    • Air cleaner assembly
    • Upper filler panel
  11. Fill the cooling system.
  12. Start the engine then idle until normal operating temperature is attained.
  13. Recheck coolant level and top off as needed.
  14. Test drive the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1998 Cadillac Eldorado

1 Answer

Need a picture of a water pump housing for a 1998 eldorado


Water Pump Removal and Installation All Engines To Remove:
  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
  2. Remove or disconnect the following:
    • Coolant into a suitable container
    • Upper filler panel
    • Air cleaner assembly
    • Secondary AIR injection control valve gm_car_cad_sev_wtr_pmp_belt_shld.gif

    • Oil level indicator tube nut
    • Water pump belt shield fasteners
    • Water pump belt shield gm_car_cad_sev_wtr_pmp_drv_belt.gif

    • Water pump drive belt (D) gm_car_cad_sev_rad_outl_hos.gif

    • Radiator outlet hose from the thermostat housing gm_car_cad_sev_wtr_pmp_and_covr.gif

    • Water pump cover bolts
    • Water pump cover
    • Heater return hose
    gm_car_cad_sev_wtr_pmp_pulr.gif

  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Remove or disconnect the following:
    • Pump from the housing:
      1. Use suitable water pump puller/installer tool (or special service tool J38816-A) to turn the pump clockwise
    • Support plate from the water housing crossover gm_car_cad_sev_wtr_pmp_rem.gif

    • Water pump
    • Seal from the water crossover
  6. Clean the sealing surfaces of the water housing crossover and the pump cover.
  7. Clean and inspect the water pump.
To Install:
  1. Install or connect the following:
    • Seal into the recessed portion of the water crossover
    gm_car_cad_sev_wtr_pmp_crosovr_seal.gif

    NOTE: The notched locking ear must be in the 7 o'clock position.
  2. Index the water pumps locking ears with the tangs in the water crossover.
  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Turn suitable water pump puller/installer tool (or special service tool J38816-A) counterclockwise.
  6. Torque the water pump
    • Torque to: 74 ft. lbs. (100 Nm)
  7. Remove the support plate from the water housing crossover.
  8. Install or connect the following:
    • Water pump cover to the heater return hose
    • Water pump cover to the water housing crossover
    • Water pump cover bolts
      1. Torque to 89 inch. lbs. (10 Nm)
    • Radiator outlet hose to the thermostat housing
    • Water pump drive belt
  9. Place the water pump belt shield in position.
  10. Install or connect the following:
    • Water pump belt shield fasteners
      1. Torque to 89 inch. lbs. (10 Nm)
    • Oil level indicator tube nut
      1. Torque to 89 inch. lbs. (10 Nm)
    • Secondary AIR injection control valve
    • Air cleaner assembly
    • Upper filler panel
  11. Fill the cooling system.
  12. Start the engine then idle until normal operating temperature is attained.
  13. Recheck coolant level and top off as needed.
  14. Test drive the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1998 Cadillac Eldorado

2 Answers

How do i change a 2004 Lincoln LS fuel pump?


Hi. here's how to change the fuel pump. The actual electric fuel pump is in the tank on the right side. The tank is directly below the rear seat. If you remove the seat bottom you will find a 6 inch or so cover. Under the cover there is a plastic, threaded collar that locks the fuel pump into the tank. The driver's side also has a pump, but it works only my venturi effect from the electric pump on the other side. This pump is used to equalize the fuel level from left to right. The drive shaft tunnel prevents all but the very top of the tank from communicating left to right.

Aug 12, 2010 | 2004 Lincoln LS

2 Answers

I have a 98 lincoln town car executive and I need to know how you change the thermostat


1. drain coolant
2. remove engine cover
3. remove the 2 bolts from water hose connection (upper rad hose connecting to)
4. remove o-ring and thermostat
5. repeat in reverse order

Feb 05, 2010 | 1998 Lincoln Continental

1 Answer

How do i change my thermostat on my 2001 pontiac aztek. also how do i remove the crossover exhaust pipe to get to the @#$%^ing thing?


Exhaust Crossover Pipe Replacement
Removal Procedure
  1. Disconnect the battery ground (negative) cable.
  2. Remove the throttle body air inlet duct.
  3. Drain the coolant from the cooling system.
  4. Remove the inlet radiator hose from the engine.
  5. Remove the thermostat bypass pipe.
  6. Remove the exhaust crossover heat shield bolts.
  7. Remove the exhaust crossover heat shield.
89160026

  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.
  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
Removal Procedure

89153578

Dec 11, 2009 | 2003 Pontiac Aztek

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...