Question about Cars & Trucks

1 Answer

How do I change front drivers wheel bearing on mitsibishi colt equipe 2005

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

Take off the brake assemble meaning remove the roater caliper clean any dirt off the control arm and axel mount take down the upper and lower ball joints then pry them down to allow the axel carrier to pivot down then there should be three bolts behind the bearing remove those and rent a barring puller from autozone then apply the puller to the barings and they should come out this May require a press installer or as in removing the barring you might have to use some wd-40 to spray on the back side of the barring and some hits with a sludge hammer to break it loose if the puller isn't allowed to force the barring out simply and to re assemble it is just the opposite also grease the axel shaft and make sure the surface is clean before installation and use anti seize on all screws and ect this shall help you out

Posted on Mar 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

emissionwiz
  • 75814 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

  • 76 Answers

SOURCE: front wheel bearings on an Acura TL

ya no prb u can do that for the front wheels...but careful that u better check the bearings of rear wheels also...so that it will be safe drive for u!!!!

Posted on Jul 25, 2009

  • 449 Answers

SOURCE: I need to change right front wheel bearing on 96 honda accord

It's not a easy job you will need a press to take the old one out and replace the new one, my advice to you is take the steering knockle out and have your local shop press the bearing out for you and put the new one in. This way you just have to bolt everything back up and your good to go.

Posted on Oct 20, 2009

agent91
  • 2100 Answers

SOURCE: 03 transit front wheel bearing

That doesn't mean you have to go out and buy a 37 mm wrench, the nut should be finger tight, if not a pair of channelock pliers will do. The nut just snugs up the bearing, too tight and it will cook. Pull the lock pin, spin off the nut, bump the rotor with a rubber hammer and the bearing should pop out in your hand, you have to replace the seal when you pull the rotor off. Sometimes the race on the inside gets stuck, sometimes it welds itself to the spindle, depends on how hot you got it, you should be able to tap it off with a hammer and a drive pin from the rear. If you can't get it to move, take a dremel to it and cut the thing in half. I hope this is what you are asking.

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

1 Answer

How do i change front drivers wheel bearing/hub set on mitsubishi colt equippe 2005 model


Take wheel off, take off axle nut and split ring, take off calliper, remove rotor, look behind hub assembly should be 2 or more bolts holding it in place, remove them and pull off hub (sometimes needs to be hit with a hammer from behind to loosen... Picture is for a link of a different vehicle but same concept 4_17_2014_3_08_27_am.png

Mar 27, 2014 | Cars & Trucks

1 Answer

2005 trailblazer knocking sound front drivers side wheel when accelerating only


First check wheel bearing. Jack front end up lifting tires off ground and see if the wheel moves by pulling on the sidewall part of wheel from top and pushing bottom towards the car does this back and forth if there is play, wheel bearing could need replaced. Take tire off and check for loose brakes, loose calipers, loose dust shields , etc. everything except rotor should be tight.

Aug 30, 2012 | 2005 Chevrolet TrailBlazer

1 Answer

Instructions on replace wheel bearing on 2005 f150 2wd front wheel


Johny brown is wrong.... the 2005 ford f150 2wd requires a rotor/bearing assembly it is really really easy to change...... jack it up remove wheel, 18 mm wrench to remove caliper mount... then remove spindle cotterpin and nylon nut (26mm? ) with any luck the rotor/bearing /hub will pull right off ...if not a make shift lever/puller should do the trick.... I actually had a bearing frozen on the spindle that i used heat and a small 3 jaw puller to get the bearing free.... if everything goes smoothly you should be done in less then 30 min

Jun 13, 2012 | Cars & Trucks

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...