Question about Chevrolet Venture

1 Answer

Do i have to reset program on chevy venture after ignition replacement?

Reset after ignition replacement?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 71 Answers

Yes

Posted on May 05, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: Reset factory alarm 1999 Chevy Venture

passager side lock and unlock the door try it out pierre

Posted on Oct 04, 2008

michigan man
  • 3533 Answers

SOURCE: how do you reset power sliding door on 2000 chevy venture

there should be information in your owner manual telling you how to do it if you have miss place your owner manual try this website to see if you can down load one for your car its www.edmunds.com and i hope i was able to help you Michigan Man

Posted on May 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why 2001 chevy venture van wont start in the cold.


Look at the ignition module or the computer. Taking off the battery cable resets the electronics. Have a diagnostic done on it to pinpoint the problem.

Nov 02, 2014 | 2001 Chevrolet Venture

1 Answer

How to reset the fuel pump on chevy venture


No you need reset your self,turn the key until all dash light come on leaves the switch like that for 30 sec.an then go back and tried

Mar 29, 2014 | 2000 Chevrolet Venture

1 Answer

Replace ignition lock cylinder


I lost my only key to my 2002 Chevy Venture Mini Van. I replaced the ignition switch. I followed the directions on how to program the new keys that came with the new switch and it didn't work. Does anyone have any suggestions on what to do. Cant afford to take it to a dealership.

Sep 02, 2013 | Chevrolet Venture Cars & Trucks

1 Answer

My Chevy venture 2002 van doesn't start. Good


You replace parts as part of your preventative
maintenance program,not to solve a problem
When working on a problem only component testing
will find the issues
You need to check for fuel pressure at the motor with a gauge
You check spark with a test plug you buy,not ground a plug
or wire on the vehicle
You can check for compression or cylinder leak down
to test some mechanical issues
I would assume ALL Fuse & links have been checked,as
well as battery voltage 12.6 v or more & cables etc
The ignition switch could be bad,turns starter but not all
the internal contacts are good

Jul 26, 2013 | Cars & Trucks

2 Answers

I put the wrong key in the ignition and had to have ignition replaced. so have new keys that are not programmed to my car.


Take it to a dealer.. only they can program a "master" key. then you can program the second key by starting the car with the master then removing the key and then starting the car with the second key within 5 seconds.

Dec 28, 2011 | 2003 Buick Rendezvous

1 Answer

How do i reset change engine oil light on a 2000 chevy venture


1. With the ignition key in RUN but the engine off, fully push and release the accelerator pedal slowly three times within five seconds.

2. Turn the key to off.

IF the CHANGE ENGINE OIL light comes back on, the engine life monitor has not reset. Repeat the procedure.

I have noticed personally that I have press my accelerator 5 times. Each vehicle has it's own idiocyncracies

Sep 26, 2009 | 2000 Chevrolet Venture

3 Answers

PUT IN NEW STEREO NOW CAR WON'T START & SECURITY LIGHT IS ON


the radio that come with car is program to pcm .if remove or put in another radio. pcm security mode kick in.it dont recognize radio it think theft so it disable car ignition so you cant start.if you get a radio the dealership has to put them in and program it.

May 31, 2009 | 2001 Chevrolet Venture

1 Answer

Program master key for 2000 chevy venture


To program a new key...
1-Turn ON the ignition, with the engine OFF, using a master Pass-Key III key (black).

2-Observe the security telltale. After approximately 10 minutes the telltale will turn off.

3-Turn OFF the ignition, and wait 5 seconds.

4-Repeat step 1-3 two more times, for a total of 3 cycles or 30 minutes.
Tech JK
-----------------------------------------------

Jan 01, 2009 | 2000 Chevrolet Venture

1 Answer

Reset factory alarm 1999 Chevy Venture


passager side lock and unlock the door try it out pierre

Oct 04, 2008 | 1999 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...