Question about 2010 Mercury Mountaineer

1 Answer

How to with on the 4x4 on a Mercury Mountaineer

I want to with on the 4x4 system on my car but i can't font the switch for it in any place in the car. It is a 2010 Mercury Mountaineer .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 156 Answers

You cannot shut off the 4x4...the truck is all wheel drive all the time.ford explorer has this option, mercury does

Posted on Jun 12, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: promblem with engine light

i recently had the same issue with my 98 mountaineer 6cyl 4x4. mine also showed the same codes for lean banks 1 & 2. That means the engine is getting too much air intake.
After about a month of a constant check engine light, i started to notice a hissing sound that came from underhood, that seemed to get louder every few days.
With a patient ear, i traced it to under the battery tray; which, by the way, looked wet from a leaking battery. Here, in phoenix arizona, batteries take a beating.
Under the battery tray there is an emissions component called the "cannister purge valve a.k.a. vapor manegment valve; attatched to it is the solenoid. there's three vacuum hoses, 2 thick 1 skinny, connected to this whole assembly. the top hose runs from the purge valve to the intake manifold.

Well on the purge valve there was pretty big hole. It was located on the chamber that the top hose connects to. Instead of the intake manifold sucking in a small amount of air from the valve, it was sucking in A LOT of outside air from the newly formed hole.

Just FYI, it took a lot of swear words and some scraped up, slightly bloody knuckles trying to get access to the valve, manuevering and such.

Posted on Apr 11, 2009

  • 1 Answer

SOURCE: 2004 Mountaineer: When my 2005 Mercury Mountaineer is running the po...

My husband had the same problem with his 02 Mountaineer about 6 months ago. I read somewhere that if you take WD40 & spray the door locks it should stop. We tried it & so far it's worked. Good luck!

Posted on Jun 07, 2010

  • 335 Answers

SOURCE: where is the 4x4 selecter located in this

This truck is an All Wheel Drive and will not have a selector switch, it will remain all wheel drive all the time.

Posted on Mar 19, 2011

bonedivers
  • 1140 Answers

SOURCE: my 4x4 light is on

just on or blinking?
awd or selective?
try changing from 4wd to auto

Posted on May 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the egr have to do with the 4x4 system an is there a fuse or relay the problem is stuck in 4x4 with no limited slip at al


The EGR has nothing to do with the 4x4 system.The 4x4 is stuck because the transfer case motor is more than likely at fault.You can get these from www.rockauto.com for under 90.00.

Oct 06, 2013 | 2001 Mercury Mountaineer

1 Answer

When putting my '04 Mountaineer in reverse or drive, with the steering wheel turned, the car fights very hard to move. Driving straight if fine. Any ideas?


Hello, Yes, It sounds like it is in 4 Wheel drive mode. Your vehicle will not make as sharp of a turn when in 4x4. You should be in 2 wheel drive on dry pavement. If you have the other system called All Wheel Drive, yours would be binding when it should not.

Check your Range Selector for the different settings. When in 4x4, the vehicle is made to take gradual turns so you don't flip it on a hill. Sometimes people mistake the Range knob for the Fan Blower switch.

Jul 03, 2011 | 2004 Mercury Mountaineer

1 Answer

My 4x4 light is on in my 2006 mercury mountaineer


just on or blinking?
awd or selective?
try changing from 4wd to auto

May 27, 2011 | 2006 Mercury Mountaineer

1 Answer

Where is the 4x4 selecter located in this vehicle.1998 Mercury Mountaineer 5.0L 4x4thank you


This truck is an All Wheel Drive and will not have a selector switch, it will remain all wheel drive all the time.

Mar 17, 2011 | 1998 Mercury Mountaineer

1 Answer

My 2002 Mercury Mountaineer is stuck in four wheel drive? Any Suggestions?


You may have to shift it out of 4x4 then reverse several feet for it to disengage.

Aug 18, 2010 | 2002 Mercury Mountaineer

1 Answer

Our mercury mountaineer door ajar sensors keep going off, and it is setting off the alarm when the car is locked.


you need to find out witch door jam switch it is they are about $40 each you can take a ohm meter and check the electrical connection. place the wires on the pins with it open then check when you press the button to make sure that the numbers change if no change on the ohm meter then that is the bad door switch

Apr 07, 2010 | 2002 Mercury Mountaineer

1 Answer

I have a 97 mountaineer with no manual. I can't figure out how to engage the all wheel drive and its a blizzard out there. Help!!!


The truck(if it's a 4x4 and not a 2x4)has an automatic setting where the truck is in automatic 4 wheel drive when it's needed. If it becomes to harsh out with deep snow, the you must turn the dash mounted switch to 4x4 high, but do not drive in 4x4 high if the ground it dry. The high 4x4 is intended for deep snow or loose sand and dirt. The switch is on the dash just to the upper left side of your radio. If there is No switch, then you may have the FULL TIME all the time 4x4 type and then it's always in 4x4 mode. Hope that helps...

Dec 22, 2009 | Mercury Mountaineer Cars & Trucks

1 Answer

1998 Mercury Mountaineer wheel bearing What tools are needed to change the front wheel bearing on a four wheel drive.


2x2 = nothing special since they are old fashion tapered bearings

4x4 = nothing special again BUT the wheel bearing is part of the hub assembly!

Jul 17, 2009 | 1998 Mercury Mountaineer

Not finding what you are looking for?
2010 Mercury Mountaineer Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...