Question about 2008 Mitsubishi Pajero 2000i

Open Question

I would like to remove the front cup holders in a 2008 mitsubishi shogun

I would like to remove the front cup holders of a 2008 shogun so that I may adjust the handbrake cable

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 76846 Answers

SOURCE: how to turn off mitsubishi shogun sport front

if there is no switch and it doesn't have the second generation smart airbag system (there is a weight sensor in the passenger seat) you can't turn it off, refer to your owners manual on this.

Posted on Aug 02, 2009

  • 1986 Answers

SOURCE: how do i adjust my handbrake on a mitsubishi

You'll need to open up your center console and look at the base of the parking brake. You should see two screws and two cables for your rear wheels. You can tighten or loosen the screws to adjust the tension on the cable and your brakes

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Wheel smokes,brake dragging

Make sure your handbrake cable is adjusted properly. Adjust the rear brake shoes down to where the wheels turn freely with the linings only just touching the drums. Be sure to pump the pedal a few times after adjusting, then try again.
The front wheels (pads and calipers) will just about never bind, so concentrate on the rear wheels. If you do suspect the front wheels, release the bleeder valve for just a second and then try again.

Jan 24, 2014 | 2001 Toyota Corolla

1 Answer

Cant find handbrake adjuster for peugeot 207

Just fixed mine, the handbrake adjuster is attached to the handbrake lever inside the consul, remove the blanking plastic section to the left of the handbrake, near the driver seat, the with a torch see in side to base of handbrake lever, you will see a vertical rod with a 10mm nut (black) adjustment is done here, quater turn at a time. my problem was the rear 2 cables had falled out of the Tee bar at the back, remove the plastic blanking plate in the rear cup holder see 13mm nut, undo this allows the consol to lift slightly, re insert cables etc, i the tied the 2 cables together with cable tie to stop them popping of the tee bar, so far so good

Jan 01, 2013 | Cars & Trucks

1 Answer

How do i adjust the handbrake cable on my 1998 seat ibiza

you dont its that simple ,if handbrake high and brake pedal low then the back drums need taking off and adjust the rear brakes manually by turning the little knurled wheel ,skim the outside of the drum with a small angle grinder to remove the lip and leave a bit of a bevel then adjust the the shoes till they catch when spinning the drum ,the cowboy way is to screw the adjuster up thats at the back of the handbrake behind the ashtray but if you do this vehicle will fail the yearly test for low handbrake readings and excessive pedal travel on the footbrake ,especially if it comes in front of me for its test

Apr 13, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

I have an '08 TL with a very annoying object sliding back and forth when I brake and accelerate. Sounds like it is under the cup holder. I removed the trim on both sides. That is where I am stumped. Is...

the center console will prob. have to be removed , there are hiden screws, be patiant and thuroly look before just ripping out cup holder.

Feb 11, 2011 | 2008 Acura Tl

1 Answer


The handbrake adjust is normally under the vehicle. The cable either splits into 2 cables or more likely, goes directly to a small curved bar. The single cable has a threaded end that goes through the bar with a nut on the end. Raise and secure the vehicle on jackstands before you crawl underneath. Look at one of the back wheels - you'll see a cable coming out to the front. Follow this cable to where it either crosses over the aforementioned bar or is connected to it. In the middle of this bar you'll see the nut from the front cable - Use a sharpie or other felt tip pen to mark the thread at the nut on the back side .Adjust this nut so it travels forward( towards the front of the vehicle) 5 or 6 threads , and check the handbrake to see if it's ok. Sometimes you can remove the cover over the handbrake and find an adjuster there - you may have to remove the center console if you have one.
Hope this helps!

Nov 06, 2010 | 2003 GMC Envoy

1 Answer

On a 2000 4 runner how do you take console off to get to radio?

Set parking brake.
Place tranny in nuetral.
Disconnect Negative battery cable.
Open center storage compartment.
Gently pry handbrake trim panel up starting at cup holders.
Gently pry shifter trim panel up and rearward.
Pull receiver trim panel away from dash.
Disconnect electrical connections.
Avoid Large YELLOW cables, these are the airbag cables.

Jun 10, 2009 | 2000 Toyota 4Runner

1 Answer

How to adjust handbrake cable


1. Raise the vehicle and release the handbrake.
2. De-adjust the handbrake cable.
  • Remove the locking pin.
  • Slacken the adjuster locknut.
  • Slacken the adjuster until the levers on the callipers have returned to their stops.
3. Paint alignment lines on the lever and caliper
4. Tighten the adjuster until the caliper levers move from the alignment lines.
5. Apply the handbrake to equalise the cable.
6. Tighten the adjuster locknut to a minimum of three clicks and a maximum of six clicks.
7. Fit a new adjuster locking pin.
8. Lower the vehicle.

Jun 04, 2009 | 2002 Toyota MR2 Spyder

3 Answers

Hello , where is the handbrake adjuster on volvo v40 - 53reg

V40 cable ajuster is situated under the rear part of center console. Remove rear tray, undo the two posi screws, remove the cup holder rubber base cover to expose one more posi screw-undo.
Now you can lift the section backond off the handbrake lever.
Look under the flexi plastic cover and find a gold nut which has a sprung retainer.
You can now effect adjustment via this nut book suggests six to seven notches from off to on for ideal adjustment.

Apr 04, 2009 | 2003 Volvo V40

1 Answer

How to adjust handbrake on hyundai excel 95, fix inside front doo

Adjusting the handbrake is easy.Between the two front seats where the cup holders are behind there is a cubby hole.This has a bottom which can be easily prised out.You will see the handbrake adjusters which you just need to tighten.

Nov 12, 2008 | Hyundai Motor 2002 Elantra

2 Answers

Toyota yaris

The handbrake adjustment is at the handbrake. Pull off the rubber boot around the hand brake. (it pulls open at the botto of the handle and slips off over it). Next locate the 10mm bolt under the rear cup holder (there may be a little felt in there covering it). Remove the bolt.

Lift the console at the rear, it should pop loose at the front and lift up. You should have clear access to the adjustment bolt. Loosen the 10mm locking nut and this should allow you to adjust the cable.

Turn the adjustment clockwise to tighten the cable and once adjusted, re-tighten the locking nut. Reverse the whole process to put the console etc back together.

Aug 17, 2008 | 2007 Toyota Yaris

Not finding what you are looking for?
2008 Mitsubishi Pajero 2000i Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides