Question about Ford Windstar

1 Answer

So i need to flush a/c lines after replacing a/c hose assembly

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 60 Answers

This is something a garage should do. There are laws pertaining to disposal of the gases within a vehicle's A/C unit.

Posted on Mar 24, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the heater core 1997 isuzu hombre


See me at website for images can only send one through this channel. www.autorepairhelp.us

Best Regards,

Master Tech Lee

HEATER BOX SHIELD
Image
Heater Box Heat Shield
Remove or Disconnect
1. Fasteners that retain heat shield to heater box assembly.
Image [ Heater Box Heat Shield
Install or Connect
1.Fasteners that retain heat shield to heater box assembly.
Tighten
-Bolts Screws to 2.2 N.m (25 lb in).
HEATER ASSEMBLY
Image ' Heater Hoses
Image ' A/C Evaporator Tube Assembly
Image ' Evaporator Core
Image ' Evaporator Core Assembly
Image ' Heater Assembly
Remove or Disconnect
1.Engine coolant. Refer to Draining and Filling Cooling System in Engine Cooling.
2.Heater hoses. Refer to Heater Hoses.
3.Instrument panel. Refer to Instrument Panel Replacement in Interior Trim.
4.Air inlet assembly. Refer to Air Inlet Assembly Replacement.
5.Vacuum lines.
Important
-Clearly label vacuum line connections.
6.Heater assembly studs inside engine bay.
7.Blower motor resistor. Refer to Blower Motor Resistor.
8.Stud inside heater core housing.
-Stud is revealed by removing the blower motor resistor.
9.Rear case screws.
10.Heater assembly.
11.Seals.
Imagt
Imagt
Imagt
Imagt
Imagt
Heater Hoses
A/C Evaporator Tube Assembly
Evaporator Core
Evaporator Core Assembly
Heater Assembly
Install or Connect
1.Seals.
2.Heater assembly.
3.Rear case screws.
4.Stud inside heater core housing.
Tighten
-Stud to 1.9 N.m (17 lb in).
5.Blower motor resistor. Refer to Blower Motor Resistor.
6.Heater assembly studs inside engine bay.
Tighten
-Studs to 1.9 N.m (17 lb in).
7.Vacuum lines.
8.Air inlet assembly. Refer to Air Inlet Assembly Replacement.
9.Instrument panel. Refer to Instrument Panel Replacement in Interior Trim.
10.Heater hoses. Refer to Heater Hoses.
11.Engine coolant. Refer to Draining and Filling Cooling System in Engine Cooling.
-Check the system for leaks.


Auto Repair Help US 699e5693-1e5b-4101-9428-b5c0b4e46f83.jpg

Sep 06, 2014 | 1997 Isuzu Hombre

1 Answer

Do i need to flush a/c lines after changing a/c hose assembly?


Yes. There will be left over metal particles in the system. Flushing removes all the oil in the system too so don't forget to add the correct amount before starting the compressor when adding freon.

Mar 23, 2014 | Ford Windstar Cars & Trucks

2 Answers

HEATER ISN'T BLOWING HOT AIR


Sounds like a restricted heater core. Remove the hoses and back-flush the heater core system with a water hose. You may want to do a complete cooling system flush while you're at it.

If you can't flush the heater core clean with a water hose, it may be time to replace.

Jan 06, 2013 | 2002 Ford Ranger Regular Cab

1 Answer

How do you install a heater core for a1991 Mazda Navajo


remove dash assembly try to back flush first or drain cooling system put water back in add cascade dish washing soap and drive a couple days if heater starts woreking better turn heat on high run engine open drain with a hose nozel on high and a large pan under drain flush all water out with engine running refill system with heat on high and vehicle running if heat still weak remove heater hoses the top should be the return line put a hose about 8 inces long on both out lets run the bottom hose to a high area where it can be suspended put a funnel in upper hose poor clr into hose until it comes out top of lower hose let set for hour and a half then flush out with water into a clear jug flush water vthrough upper hose then if u have air compressor have a 6 inch hose attatched to upper pipe and blow out core into same jug until the jug has clean and clear water refill cooling system and drive if heat doesnt work at first put engine under a load to release residule deposits in heater core and it should start flowing

Apr 01, 2012 | Cars & Trucks

2 Answers

Broken coolant line.


I'm not sure if you can buy just that piece, it's recomended that you replace the entire heater hose assembly.
For reference the NAPA p/n is BK 8155114 go to thier web site and verify this is the part you're needing to replace.
You should flush and replace the coolant if it old.
Hope this help you with your problem.

Jun 10, 2010 | 1997 Mercury Sable

2 Answers

My ac compressor locked up. What needs to be


I would suggest leak testing it you can take hose with clamps to the outlet and put a psi gauge on it then hook a compressor to the other end with a hose with clamps. This will show you if you have any obvious leaks you dont need alot 10psi and hold as long as you would like atleast a min you can also spray it with soap bubles to be sure. the condenser if its not leaking would be fine with a flush.

Apr 06, 2010 | 1998 Chrysler Town & Country

1 Answer

1996 jeep grand cherokee blower works but no heat. I flushed heater core with hot water, replaced thermostat, and water pump is circulating. Vacuum line?


Since your blower is working and it is a heat issue,thats where we'll start,First thing is have you checked the coolant level in the radiator when engine is cold,make sure it is filled to top,next verify you have coolant in reserve ,Start your van and get it up to normal operation temperature,If your heat gauge on the dash works correctly it should be 190 degrees,Now lift the hood and locate the two heater hoses going into the heater assembly at the fire wall,Both hoses should be hot to hold on to,if both are hot and no heat inside your problem will be the blend air door in heater assembly.
if neither hose is that hot you need to replace the thermostat in the engine to get it up to 195 degrees.
if one hose is hot and one is luke warm then the heater core is blocked and to blame. hope this helps you.

Jan 12, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Changed the thermostat, still no heat. Is there a valve of some sort in the heater hose lines or on the heater assembly that controls the hot water?


when the vehicle is cold take the radiator cap off and start the vehicle let it run with it on defrost at full blast until the vehicle gets to running temp,if there is still air in the system it will blow cold air if that doesn't work then check to see if the vacuum lines that run the blend door in the heater box have came off (depending on year)

Dec 28, 2009 | GMC Jimmy Cars & Trucks

3 Answers

Over heating 1998 cherokee


Yes - Your radiator not only needs to be flushed you could also have an inexpensive procedure done at any reputable radiator shop called "rodding out" and then heat flushed. If I remember correctly 98 Cherokees have a 4.0 in line 6 cylinder motor that has a aluminum radiator. If you remove your radiator yourself (drain detach hoses and unbolt assembly) and bring it to the radiator shop you could get this done really cheap. If you are not comfortable doing this, have them do it for a slightly higher fee. This should really help. NOTE: When adding radiator fluid from now on, use 50/50 premix or if you mix it yourself always use DISTILLED Water. This prevents corrosion buildup in your system. Good Luck!!!

Nov 07, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...