Question about 2001 Hyundai XG300

Open Question

Transmission control module

Where is tcm module

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2009 Chevy Avalanche LS and I got the P0700 code, how easy is this to fix? where is the TCM located? If this is a dealer service how much?


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination
The transmission control module (TCM) uses the (GMLAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure affecting emissions has occurred in transmission control system. When the ECM receives the message from the TCM, DTC P0700 will set.
DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.
This is something best left to a qualified repair shop , doesn't need to be the dealer ! AMMCO could fix it . This code is telling that other codes are stored in the transmission control module . Need a professional type or factory scan tool to check these . As to how much it will cost , no telling without knowing the codes in the TCM !

Apr 28, 2017 | Cars & Trucks

Tip

I get code p0700 after an OBDII scan.


P0700 Transmition Control system is the transmission control module.
The transmission control module is a separate computer module, you need to read codes stored on transmission control module.

If there are no transmission code stored, then there is a bad Transmission Control Module (TCM) ground circuit or a bad TCM. In that case the ground to TCM must be tested, and TCM eventually replaced.

Faults that can cause troubles when shifting from first to second gear are : transmission fluid, speed sensor, TPS, transmission shift solenoid, gear box problem, TCM, neutral switch, torque converter problem.

The best thing to do is scanning TCM codes.

on Dec 02, 2009 | Jeep Wrangler Cars & Trucks

1 Answer

I replaced the TCM in my 2005 Chevy colbolt, light come on but car won't start, turn key and anti theft icon comes on but doesn't stay on


TCM ? transmission control module ? Did you have it programmed ? Reprogram the TCM. Refer to Control Module References for programming and setup information.
Transmission Control Module Programming and Setup
The transmission control module (TCM) must be programmed with the proper software/calibrations. Ensure that the following conditions exist in order to prepare for TCM programming:
• The battery is fully charged.
• The ignition switch is in the RUN position.
• The Techline equipment cable connection at the data link connector (DLC) is secure.
Program the TCM using the latest software matching the vehicle. Refer to up-to-date Techline equipment user instructions.
If the TCM fails to program, proceed as follows:
3.1. Ensure that the TCM connection is OK.
3.2. Inspect the Techline equipment for the latest software version.
3.3. Attempt to program the TCM. If the TCM still cannot be programmed properly, replace the TCM.

Feb 08, 2017 | 2005 Chevrolet Cobalt

1 Answer

2hat does code #P0700 mean on a 2007 Chevy Silverado. 4x4 mean


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination
DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.

The transmission control module (TCM) uses the (GMLAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure affecting emissions has occurred in transmission control system. When the ECM receives the a message from the TCM, DTC P0700 will set.
You don't say which engine your's has ! Or which transmission .
Automatic Transmission - 4L60-E/4L65-E/4L70-E

You need to have TCM checked for codes .

Dec 22, 2016 | Cars & Trucks

1 Answer

My 2004 Saturn ion 3 has 2 codes coming up u2105 p0700 an it won't go in drive or reverse what could it be


First off you need to understand your vehicle has several control modules on board . The PCM - engine computer , TCM - transmission control module , SRS - air bag module , Anti theft , antilock brakes , An these modules all are able to talk to each other on a communication network , On your vehicle it happens to be the CAN data bus !
The transmission control module (TCM) uses the controller area network (CAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure that affects emissions has occurred in the transmission control system. When the ECM receives the correct message from the TCM, DTC P0700 will set.
Which transmission does your vehicle have ?
Automatic Transaxle AF23-5
OR
Automatic Transmission VT25-E
DTC U2105-U2199
The controller area network (CAN) serial data line is a high speed serial data bus used to communicate information between the engine control module (ECM), body control module (BCM), and the transmission control module (TCM). Typical data-transmission speeds must be high enough to ensure the required real-time response is maintained. The CAN serial data line does not communicate with the scan tool via the data link connector (DLC). CAN serial data information is interpreted by the BCM and transmitted to the serial data line by the BCM.
I suggest you take this to GM dealer or some other ASE certified repair shop .

Aug 13, 2015 | Saturn Cars & Trucks

1 Answer

I have grand cherokee 2001 limited the code p0700 is apper the gear is started scend shift espically in morinig


possible causes
Shorted or open circuit within Transmission Control Module (TCM)
- Faulty Transmission Control Module (TCM)
symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transmission shifting problems
p0700 description
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Read more: http://engine-codes.com/p0700_jeep.html#ixzz2hihK6PVo

Oct 14, 2013 | 2001 Jeep Grand Cherokee

1 Answer

1997 honda accord tranmission problem code p0700 drive 4 flashes


Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.

Symptoms Symptoms of a P0700 DTC may include:
  • Malfunction Indicator Lamp (MIL) illumination
  • The transmission may exhibit drivability problems like slipping, etc.
Causes More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
Possible Solutions For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.
If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.

Oct 20, 2012 | 1997 Honda Accord

1 Answer

Wont start trouble codep0700 is the only code


Hi there:Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.
More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day

Mar 02, 2012 | 1996 Chevrolet Blazer

1 Answer

P0700


Hi there:Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.
More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.

Mar 02, 2012 | 1996 Chevrolet Blazer

3 Answers

What is a tcm


Hi

Thanks for using FixYa. The TCM means Transmission Control Module which is part of the PCM or Power Train Control Module and is located in front of the left front tire. You can access it by removing the fender liner.

Please do rate the solution and revert for further assistance.


Thanks
Rylee

Sep 18, 2009 | 2000 Dodge Caravan

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...