Question about 2001 Suzuki Grand Vitara

Open Question

Turn signal fuse location

Blinker andparking light not working

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 4 Runner blinker problem


The hazards use a separate relay. listen for signal relay clicking to locate the correct relay. Consult your owners manual for fuse and relay layout.

May 26, 2017 | Toyota 4Runner Cars & Trucks

3 Answers

Turn signals quit working on my 99 lincoln town car! Everything else works but the blinkers! Fuses and bulbs ok! Thank you!


under the dash is a blinker solenoid. it constantly clicks when the turn signals are on. could be bad. Does the four way hazards work? if they do then it will be your turn signal switch (the handle you use to turn on the turn signals.) I've been a mechanic for 10 yrs. Hope this helps

Feb 22, 2011 | 1999 Lincoln Town Car

1 Answer

My blinkers and flashers all quit working at the same time. Indicator lights in the dash won't even light up. Do flashers and blinkers run off the same fuse?


The do not run off the same fuse but they do run off the same blinker. Try turning on the key, click the left/right (check both) turn signal and then operate the 4 ways on and off at the same time. Work the 4 way switch back and forth 10 to 25 times and see if you get any short winks or blinks from the system.
Turn signals are usually on their own fuse in the glove box and hazard are on with the brake fuse. If this does not work, I would look at the blinker. It is possibly bad. Check each pin of the blinker and see if there is power there when you turn on the 4 ways or turn signals. Replace Blinker. Make calls to parts stores and dealer for location of this blinker.

Mar 21, 2010 | 1995 Buick Regal

1 Answer

Both turn signals do not work on 87 mercury sable


The fuse block is usually located on the left side under dash or behind a small cover on that side. If the fuses are ok change the signal relay, after that the signal/light switch on the steering column.

Jul 24, 2009 | 1987 Mercury Sable

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

1 Answer

Where is the heater and turn signal relay located 1992 caravan


These are seperate fuses and seperate turn signal falsher which evenually go into the same wiring. See my answer to your previous question. Good luck and hope it helps.

Jan 19, 2009 | 1992 Dodge Caravan

1 Answer

YJ Blinker Relay


Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Aug 30, 2008 | 1988 Jeep Wrangler

3 Answers

Blinkers not working


Did you check the bulbs? If one bulb is burned out, the blinkers won't word on that side. You could have one bulb burned out on each side. Start the car, put left signal on. Check front and back lights. Is one light on but not blinking? If that's the case, the light that's not on at all is burned out and has broken the circuit so the good light stays on and won't blink. Check the other side. You also have a 'flasher' , actually 2. One for emergency flashers, one for the turn signals. It could be that the turn signal flasher is shot. You just have to unplug it to remove. It's probably located near the fuses. good luck countrycurt0

Aug 10, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Suzuki Grand Vitara Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...