Question about 1990 Chevrolet Lumina

1 Answer

Oil filter I can't find it to put new one on

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

,your oil filter is in the front of the engine, if you look down where fan is ,first your radiator then the fan you will see the oil filter coming out of front of engine

Posted on Sep 27, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Oil leaks from the place oil fiter fit on motor


Perhaps but it could also be a bad oil filter seal. Might want to remove the filter to inspect both the seal and the housing.

Jan 12, 2014 | Audi A4 Cars & Trucks

1 Answer

Steps to change the oil


Get an oil pan and place under drain plug on oil pan of the motor, remove drain plug and make sure while oil is running out that you have the pan in position to catch the draining oil. Locate oil filter and remove, sometimes you can do this by hand after wrapping with a rag, but you may need an oil filter wrench. It will have oil in it so be careful as you unscrew it to quickly turn the end with the threads up so as not to spill the remaining oil. Put the filter threads down on the drain pan to drain the filter. Make sure the new filter and the old filter are the same. I would put the threaded ends together to make sure the rubber seal is the same size. Put a couple drops of new oil on the new filters rubber seal and spread. Screw the new filter on being careful not to crossthread it, and tighten down by hand. Wrap a rag around the filter and give another quarter turn to tighten. Replace drain plug at oil pan and fill with oil. Start the motor and let run for 10-15 seconds and turn off and check oil level again, adding more if needed, but dont overfill.

Mar 25, 2013 | 2002 Chevrolet Impala

3 Answers

Do I need a mechnic for changing oil in my chevi


No. The oil is very easy to change. All you need is a filter wrench and a 15 mm. socket, and a drain pan. Get under the truck and the oil filter is right there and the drain plug is in the oil pan. Drain the oil first, then remove the oil filter with the filter wrench. Take your finger and dip it in the oil and put a film of oil on the new oil filter gasket. Then install the new oil filter. Once you install the new oil filter, put the drain plug back in. Then put 5 quarts of new oil in the oil fill.

Jan 11, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

I want to drain the old oil out so i can replace with new oil,, how do i empty it?


Under your car in the front should be the oil pan. It has a bolt on one of it's sides. Loosen this bolt and take it out. Don't forget to put something under your car to catch the old oil. Also, change the oil filter. You should see the oil filter while you are under your car. Before putting in new oil and filter, make sure you put the bolt back in the oil pan. Put a little new oil into the new filter and wipe some oil with your finger around the oil filter rubber gasket. Make sure you don't overfill with oil !

Dec 30, 2010 | Ford Futura Cars & Trucks

1 Answer

How to change engine oil and oil filter


Drain the oil out the bottom of the oil pan there is a plug its just a bolt be careful not to drain the tranmission fluid. after all oil is drained put plug back in. remove oil filter (probably goin to need oil filter wrench). put new oil filter in place of the old one put small amount of oil on the gasket on new oil filter this will help make it easier to remove next time. if you can fill new filter up with oil before installing this will prevent dry starting. fill motor with recomended oil type and amount. you can go to any auto parts store they will set you up with everything you need an tell you the correct amounts. They even sell dvds now that will give you step by step instructions if you need further help.

Nov 11, 2010 | 2000 Mazda 626

1 Answer

How do i change the oil filter on a 1991 cutlass calais? any special tools?


YOU NEED 4.5 QUARTS OF OIL WITH NEW OIL FILTER.YOU NEED OIL FILTER WRENCH YOU NEED WRENCH TO REMOVE OIL DRAIN PLUG.YOU NEED A DRAIN PAN CATCH OLD OIL.NEED LATEX GLOVES TO KEEP GETTING OIL ON HANDS.OIL DOES CAUSE SKIN CANCER.NOW YOU CRANK CAR UP LET IT IDLE 5 MINUTES TO LOOSEN UP OIL AND SLUDGE.TURN OFF ENGINE.SAFELY RAISE SUPPORT VECHICLE ON LEVEL SOLID GROUND USING JACK STAND.PLACE DRAIN PAN UNDER OIL PAN THEN REMOVE OIL DRAIN PLUG LET OIL DRAIN OUT UNTIL IT STOP DRIPPING. PUT OIL DRAIN PLUG BACK IN OIL PAN. THEN SLIDE DRAIN PAN UNDER OIL FILTER REMOVE OIL FILTER LET OIL DRAIN UNTIL IT STOP DRIPPING.TAKE CLEAN PAPER TOWEL WIPE OIL FILTER SEAL SURFACE MAKE SURE NO DIRT ON SURFACE.TAKE NEW OIL FILTER POUR NEW OIL IN FILTER UNTIL ITS ALMOST AT TOP THEN.RUB CLEAN OIL ON NEW OIL FILTER SEAL.THEN PUT NEW OIL FILTER IN PLACE HAND TIGHTEN IT.POUR 4 QUARTS NEW OIL IN ENGINE CRANK CASE USING A FUNNEL.WHEN DONE.CRANK THE ENGINE CHECK FOR LEAKS AT OIL FILTER AND OIL DRAIN PLUG.IF ALL IS GOOD JOB WELL DONE.

Aug 11, 2010 | 1991 Oldsmobile Cutlass Calais

1 Answer

How do i do a self oil change on a 1995 jeep grand cherokee


locate oil drain plug on oil pan,engine off. take out oil plug with wrench, drain oil into a big pan or similar. when oil is drained remove oil filter and put new one on, put some new oil on filter seal with finger then screw on to car as tight as you can get it by hand. do not use a fiter wrench to tighten filter only hand tight. use oil filter wrench to take off old oil filter. when filter is on put plug back in oil pan and tighten. then add your new oil to reccomended oil level.

Jul 21, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Changing the oil


Buy four quarts of oil, oil filter, you'll need couple sockets, oil pan, jack stands, hoist, and strap wrench.

(1) Park vehicle on flat surface.

(2) Open hood and unscrew oil filler cap.

(3) Take oil pan and yourself under vehicle and unscrew drain plug to allow old oil to drain out of vehicle.

(4) As oil is draining from vehicle, go ahead and prepare new oil filter by applying some oil to the rubber "O" ring on new filter. Thats therubber ring on the filter that butts up against the block when thefilter is screwed and tightened into place.

(5) Now that the new filter is ready to be used go ahead and put drainplug back into vehicle oil pan at this point all old oil should havebeen drained out.

(6) Go ahead and use oil filter wrench to take off old oil filter, youmay be able to use your bare hands to take this off as these arejust hand tightened let old oil drain from oil filter housing for a fewminutes. Wipe area clean with a rag before putting new filter on. Nowyou can install new oil filter remember to hand tighten new filter onlyyou won't need to use oil filter wrench to tighten oil filter

7) Now you can add new oil by pouring it into the same place you took off the oil filler cap.

(8) After pouring in oil check oil dipstick to make sure you havepoured the proper amount, this is usually done by making sure new oilis at the top of of the crossed section that is at the bottom of thedip stick.

Dec 29, 2009 | 2006 Chevrolet Malibu

1 Answer

Change the oil on a 2000 Dodge Caravan


Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.

Nov 21, 2009 | 2000 Dodge Caravan

1 Answer

2004 jeep grand cherokee, 4.0, change oil without filter change,


Not sure why the question is even being asked, but you can change the oil yourself in about 15 minutes; simply jack the front end, put a pan under the oil drain plug, open the plug, let it drain, put the plug back in, and add new oil.

Take it to any outlet that changes oil (Wal-Mart, for example, charges about $18, some places charge as little as $15) and they'll include a new filter because otherwise you're running new oil through an old filter, which defeats the idea of the oil change. You can ask them not to put on a new filter, but you'll still pay the base price.

My question is, why would you not want a new filter if you're changing oil.

Let me know if this answers your question.

XMinusOne@gmail.com

Dec 10, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1990 Chevrolet Lumina Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...