Question about 2002 Dodge Ram Maxi

1 Answer

Door ajar light is on and all doors are shut tight

Where is the sensor
what fuse number should I check

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 365 Answers

Its not a fuse...it's a sticking door "button" or possibly a ground-fault of one of the door buttons. On the Dodge they're in the front of the door jamb about 1/2 way down.
Good Luck

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fuse for oxygen sensor


I doubt that there is any fuse for oxy sensor. The system computer is connected directly to the sensors, and no fuse is involved.

May 23, 2016 | Cars & Trucks

1 Answer

Why doesn't it start?


I ran into this once when I changed a 2000 engine with a 2001 engine. The crankshaft gear for the timing belt was different. One had 2 ears for the crank angle sensor and one had 4. To check if this is the problem, pull all 4 sparkplugs, hook them to your plug wires, turn the engine over and see if you only have spark to 2 cylinders. If that's what you find then you will need to replace the crankshaft timing belt gear.
If that's not it, and you have spark to all 4 cyls., check your fuses. It could be a fuel pump fuse or ECM or an number of other fuses.
Good luck
Dave

Nov 02, 2015 | 2005 Subaru Forester

1 Answer

HONDA NOT STARTING AFTER ECM RESET


Resetting the ECM does not lead to any starting problem, though the idle speed re-learning is required. Check carefully there could be something else that is creating a problem for you.
Check:
- The fuse number 20 (15 Amp) located in under the dash fuse/ relay box, if it is blown.
- Check battery.
- Check starter.
- Check if there is enough fuel in the fuel tank.
- Camshaft Position (CMP)sensor.
- Crankshaft Position (CKP) sensor.
- Fuel pump circuit

Feb 21, 2013 | Honda City Cars & Trucks

1 Answer

Changed all o2 sensors and crankcase breather pipe still got 1646 1647 codes


Have you checked that the two o2 sensor fuses are intact? Can't remember the fuse numbers but they are green, under the bonnet and one is the last fuse forward end in the row nearest the relays the other is the next green one in the same row any doubt consult owners handbook for the correct fuse numbers

Feb 09, 2013 | 2002 Jaguar X-Type

1 Answer

Troubleshooting PO135


Code is for the O2 sensor heater bank one sensor one.
The sensor is not heating up fast enough for the computer to get data from it.
I would check for voltage and ground at the sensor first.
Both O2 sensors get power from the same 15 amp fuse number 29 marked "OXY SEN" so I doubt it is the fuse since only one code was set.

Jul 22, 2012 | Cars & Trucks

1 Answer

My 2004 hyundia Santa fe won't start it just die out a code came up 0335 changed crankshaft sensor still won't start changed camshaft sensor won't start changed ecu same thing there is no spark to spark...


Check fuses under the hood. When the crankshaft sensor shorts, it often blows this fuse. It is a 10 amp fuse. I don't remember what number it is off hand but it will be efi related.

Feb 17, 2011 | 2004 Hyundai Santa Fe

2 Answers

Code error number p0135


P0134....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)


P0135....O2 Sensor Heater Circuit (Bank 1 Sensor 1) heater in the O2 sensor has packed up first sensor before the cat

Nov 27, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My 94 jeep grand cherokee has no spark or fuel to the engine. the check engine light will not come on and the security system doesnt work. gas down the throtle boy doesnt let it start.


1-check fuses if fuses ok go number 2.
2-check for power to the crank shaft sensor (test light) for a positive if no positive replace asd relay.
if you got power to sensor check for signal while cranking on the engine (connect the test light to (+) on battery if no signal replace the sensor. hope this helps.

Jan 11, 2010 | 1994 Jeep Grand Cherokee

2 Answers

02 Chevy Trailblazer: Fuse # 47 keeps blowing. When it does, the key cannot be removed and the transmission is sluggish in 1st gear. I am replacing fuses daily. Any thoughts on a fix? Is it the...


there is a short circuit in the system, check for a broken wire, also check the fuse and relay, make sure use use the wright fuse type an number.

Jul 31, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

Merc c180 1995 manual, speedo not working and abs light on


hello,try to check your fuse in excess voltage protection relay,maybe busted or check fuse number 4,12,,ty

Apr 16, 2009 | 1997 Mercedes-Benz C-Class

Not finding what you are looking for?
2002 Dodge Ram Maxi Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...