Question about Cars & Trucks

1 Answer

Brakes will not bleed properly. pedal goes all the way to floor with no resistance at all with engine on or off.

I tried bleeding brakes but no resistance when pumping brakes. There is no braking at all.

Posted by on

  • Gene Maddox
    Gene Maddox Mar 22, 2014

    I followed Suburu procedure to the letter as in the correct sequence. Why is there no brake pedal resistance

  • Gene Maddox
    Gene Maddox Mar 24, 2014

    Had to bleed system a couple of times. working great now.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Hi there, have you checked the master and slave cylinders on the vehicle ? This is 10 to 1 a fault. If you need further advice try contacting or emailing me on debbie@norbrake.co.za and I will forward your message through to a brake specialist here that could advise you.

Posted on Jun 24, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleed brake but still goes to floor


you need to bleed it with the car running

Nov 25, 2012 | 2003 Kia Rio

1 Answer

When bleeding brakes have good pedal with engine off. with engine running pedal goes almost to the floor what is wrong


can you here a hissing sound when you push the brake while its running? if so then you have a bad brake booster, need to replace it, the hissing is actually the vacuum that builds within the booster escaping thru the seal in the booster

Sep 09, 2012 | Oldsmobile Intrigue Cars & Trucks

1 Answer

Hi got fiat stilo jtd 02 plate clutch pedal has no resistance just goes to the floor could it be the cable or somethingelse please help


Hi, I've got the same problem. They run on brake fluid not cable. I started to bleed the
Clutch to adjust the bite point but after one bleed the pedal went to the floor and can't get it back. Tried pressure bleeding it but seems to be no fluid coming out of the bleed nipple. No leaks. Can any one help??

May 21, 2011 | 2006 Fiat 124

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

2 Answers

98 wrangler - brake pedal goes all the way to the floor. The master cylinder and all brake lines are free of leaks. I'm not losing any brake fluid anywhere. I replaced the booster that is attached to the...


You changed the master cylinder and vacuum booster and have no leaks anywhere, but did you bleed the entire brake system after you did this work? A little bit of air in any of the lines will make the brakes ineffective.

May 30, 2017 | 1998 Jeep Wrangler

2 Answers

Got a 94' chevy 1500 having brake problems, and replaced the master cylinder and bled the lines. but the pedal is still not working right, the pedal when pushed with the truck running will just go to the...


With he engine running your pedal action is assisted greatly by the brake servo. The servo is a large diaphragm that is acted on by the suction delivered by a vacuum line from the the intake manifold. The fact that the pedal goes to the floor when the engine is running just shows how much assistance the engine suction provides to your foot pressure. It is obvious that you still have air in your system. I would suggest that you top up the master reservoir, start your engine and pump the brakes quickly until you feel some hard back pressure. This will ensure that the brake pistons have been fully extended. Starting with the most remote caliper (right rear) bleed off about half a pint of fluid. Ensure that no air is allowed to **** back in via the bleed nipple at any time. Refill the master reservoir. Next the left rear caliper, bleed off about a quarter of a pint. Refill reservoir. Bleed off a about quarter of pint from both front brakes. This should sort it out.

May 13, 2010 | 1994 Chevrolet C1500

2 Answers

Brake pedal still goes to floor 2000 GMC Jimmy


It's very possible to be the master cylinder, the o-rings on the piston could be worn, letting the fluid seep back through instead of getting full pressure through the lines. Could also be the brake booster.
Try changing the master cylinder first, which is cheaper and easier, and see if there is a difference, you'll need to bleed the brakes again.
To check the booster,
With the engine off, pump the brakes until the pedal is hard, then hold pressure on the brake pedal and listen for air escaping, or the pedal goes slowly to the floor, Do that after the master cylinder has been changed, at least that will be eliminated.

Sep 15, 2009 | 2000 GMC Jimmy

1 Answer

Replaced front pads now brakes bleed to fluid however the pedal goes to the floor and sounds like air? ideas??? How do we check if Master Cyl, is going or calipers etc...


fill mc resovoir with fluid, open all bleeders and let it gravity bleed, while it is bleeding monitor fluid constantly as to not let it run dry, after a bit watch the bleeder screws for fluid flow and air bubbles, when bubbles stop close off bleeders one by one, check pedal for resistance and air in system, if pedal is firm , then good, if not then time to try a pressure bleeder... you may take it to a shop with the proper tools to pressure bleed the system....

Aug 07, 2009 | 2001 Chevrolet Blazer

1 Answer

Brakes


The brakes just need to be bled properly which take 2 people or a bleeding pump,Please tell me how you are bleeding the brakes.

May 17, 2009 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...