Question about Cars & Trucks

1 Answer

99 astro van changed turn signal switch because when I would turn it left it worked fine but when I turn it right all the 4 blinkers come on! I still dont have a clue why its doing that anybody have a clue fuses relays and bulbs are good

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,714 Answers

Check the hazard switch and relay.

Posted on Mar 22, 2014

  • 8 more comments 
  • javi mascorro Mar 23, 2014

    Well the hazard switch is on the turn signal switch and well I put in a new relay also do you think it might be grounds?

  •  Russ Hill
    Russ Hill Mar 23, 2014

    it could be a earthing problem. been trying to find the earths on this model but the earths use other parts 2, has the turning switch ever made a crunching sound. .... there is another test you can do there should be a fuse in fuse box remove it and check the turn signals switch if thats fine and no lights on. if you get the lights on its got a cross over from some were in the lighting circuit. means you getting live from another source, if it does this it may be the continuous live wire on the right side rear wiring.

  •  Russ Hill
    Russ Hill Mar 24, 2014

    my betting is its the switch though as its 99 and a van so its on the move alot at turning switch will have a lot of use.

  •  Russ Hill
    Russ Hill Mar 24, 2014

    do you have any other problems on the switch says there is a few types

  • javi mascorro Mar 24, 2014

    Well the switch got replaced new! But yet still does the same! Yesterday I even turned on the lights and even the license plate lights blink too now!

  •  Russ Hill
    Russ Hill Mar 24, 2014

    do you have a meter ? or can you borrow one. put it on normal resistance or beep and put on end on the battery and then the other lead to the shell there should be no resistance.. if fine then take out one side of the rear lights and do the same to that end the earth wire and then the shell. if that is fine it must be some were in the dash that the problem is. it could even be the fuse box. also check that the floor is not wet or damp. as water could be the problem.

  • javi mascorro Mar 24, 2014

    Resistance is good and well now my instrumental cluster blinks also and radio does too

  •  Russ Hill
    Russ Hill Mar 24, 2014

    should be no resistance at all. digital reading should be 000 and beep. there is definitely a leak over to other systems on the wiring if its moved over to radio and instruments cluster its an earth leak somewhere. but if it has made it worse with the new stick. are you sure the new stick you got was working one ? it would stay the same as it was before or better with the new stick but worse sounds like there is a fault with that one.

  • javi mascorro Mar 25, 2014

    Well it cost me like 170 or so at autozone brand new! Well when I do test it from the switch it throws out perfect current until it reaches fuse box and relay under dash! Could that be it? Is there a way it could be shorted out?

  •  Russ Hill
    Russ Hill Mar 25, 2014

    the relay could be damaged or there is a short in the fuse box. would say you were robbed at auto zone seen online new 75 Dollars. can you find the main earth wire in the fuse box and try that to the shell like in the battery.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: 99 Rodeo Right turn signal makes brake lights blink

TURN SIGNALS WILL FEED BACK THROUGH THE TURN SIGNAL SWITCH.THEY ARE INDEPENDENT OUT SIDE ON THE CAR BUT NOT IN THE SIGNAL SWITCH.REPLACE THE SIGNAL SWITCH

Posted on Jan 03, 2009

cadman000
  • 607 Answers

SOURCE: 02 Buick Century turn signal problem

try 2 new bulbs

Posted on Apr 21, 2009

cecandtylers
  • 4 Answers

SOURCE: Right turn signal not flashing on 1992 Buick LeSabre

Back in the late 80's early 90's GM's turn signal switch in would get loose afetr some use and one side or the other turnsignals wouldn't flash or only the third bake light worked and/ or you couldn't flip your headlights to high beams and have them stay on without holding the turn signal arm back. Perhaps if turnining the bulb over as Mr. Scary suggested proves fruitless. and you may explore that option. Get an assistant and have him watch your blinkers tailights etc. and turn your blinker on and push the blinker arm firmly toward the dash and see if that resolves your problem.

Posted on May 02, 2009

  • 5 Answers

SOURCE: Rear right turn signal does not work.

check the front right bulb

Posted on Sep 17, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheres the turn signal relay located on the 99 windstar


If your other blinkers work ,it's not the flasher . Probably a wring problem or the bulb . Find a wiring diagram at www.bbbind.com an trouble shoot the circuit . Look at you tube , there are a lot of basic electric trouble shooting videos , an a few on reading wiring diagrams .

Nov 13, 2015 | Cars & Trucks

1 Answer

Can I remove a damaged ignition key switch from a 99 astro van?


yes, that is what a large srew driver is for, hehe.
However you will need to pull the stering wheel
and remove the internal blinker assembly and remove a bolt holding it in place, if you need to move the tumbler use a srew driver and force it around. This
should be done by a good mechanic, even we have a fun time...If it is design like I think

Feb 10, 2010 | 1999 Chevrolet Astro

2 Answers

1995 Astro Van Signals not working but hazards working fine. Switch in steering colloum is fine.


sounds like the turn signal relay. its under the dash on the drivers side.

Sep 13, 2009 | 1995 Chevrolet Astro

2 Answers

When lights are on. Right blinker stays on sollid.


you need to change the bulb in either the front or back on the side thats not working

Jan 11, 2009 | 2002 Chevrolet Impala

1 Answer

99 Rodeo Right turn signal makes brake lights blink


TURN SIGNALS WILL FEED BACK THROUGH THE TURN SIGNAL SWITCH.THEY ARE INDEPENDENT OUT SIDE ON THE CAR BUT NOT IN THE SIGNAL SWITCH.REPLACE THE SIGNAL SWITCH

Jan 02, 2009 | 1999 Isuzu Rodeo

3 Answers

99 Rodeo Right turn signal makes brake lights blink


could be both unrelated issues at the same time

worn indicator stalk
faulty relays

adjust or test the brake pedal stop light switch

Mar 22, 2017 | 1998 Isuzu Amigo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...