Question about 1998 Ford Explorer

1 Answer

My 1998 ford explorer has bank 2 lean and bank 1 rich.

Has a rich and lean code

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 62 Answers

Needs new fuel injectors

Posted on Mar 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: Code #P0171 & code #P0174

The most common problem on a Ford with these codes is deteriorated PCV hoses. Check the hoses from the PCV valve to the intake manifold. Pay special attention to the rubber elbows. They often crack on the inside curve and the crack is hard to see.

Posted on May 22, 2008

  • 24 Answers

SOURCE: i have error codes p0156 p0161

  Check the wire harness near the top of the engine in the rear. They were good for rubbing through on the trans fill tube bracket. Judging by the code you have 4 sensors. you would be interested in the drivers side rear sensor.

Posted on Nov 13, 2008

emissionwiz
  • 75797 Answers

SOURCE: I get a DTC P0133 code on my 1998 Ford Explorer V8

it may be a defective O2 sensor here is th difinition:
P0133 - Heated Oxygen Sensor (HO2S) Slow Response Bank 1 Sensor 1 , this is the sensor on the side of the engine that #1 cylinder is on, it is the sensor before the cat.

Posted on Jan 14, 2009

  • 1201 Answers

SOURCE: Diagnostic Codes p0171 bank 1, and p0174 bank 2 (too lean)

Those codes are for the oxygen sensors, lean fuel mixture on both banks. Change them, problem with stalling and rough idle should go away.

Posted on Apr 23, 2009

  • 149 Answers

SOURCE: 96 ford explorer codes too lean bank 1 and 2

1. a vacuum leak. 2 low fuel presure. 3 bad airflow sensor.4 an exhaust leak before bank 1 or bank 2 o2 sensor 2

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 ford explorer with a rich/lean code


I would check for a vacuum leak somewhere. Like the post for the pcv hoses and elbows to the intake manifold gaskets not sealing. Check with at scan tool the fuel trims to see how the engine is running. If the long term fuel trim is over 10 % then there is a vacuum leak. It is rare for a lean running bank and at the same time a rich running bank. The only thing that could be possible cause for that would be the mass air flow sensor or the hose to the throttle body is not sealing causing unwanted air to get passed the MAF. These engines have a problem when it is cold the manifold gaskets not sealing and then when the engine is warm to seal and the fuel trims be high when cold and then be normal after it warms up

Mar 22, 2014 | 1998 Ford Explorer

1 Answer

97 ford expedition has a code 171 and 174 bank 1 and 2 lean what do i do to fix this


Code 171 and 174 are for bank 1 and 2 running too lean. The engine has compensated as rich as it can go, and it is still to lean. This does not necessarily mean your mixture is bad, but something (a sensor) is telling the ECM to correct lean. The oxygen sensors alert the ECM to how lean/rich the exhaust is, and then the ECM trips a code. Maybe you have a bad oxy. sensor, but since there are 4 of them (2 per bank), I don't think they could all go at once.

Aug 31, 2013 | 1997 Ford Expedition

1 Answer

I have a 1998 ford contour that has codes p1130 and p1131 on it what could be the problem. the check engine light is on


H40 DTCs P1131, P1132, P1151 AND P1152: UPSTREAM HO2S NOT SWITCHING. DTC P1130: FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN)
    Diagnostic Trouble Codes (DTCs) P1131 bank 1 (Cylinder 1) and P1151 bank 2 indicate the fuel/air ratio is correcting rich for an overly lean condition. The HO2S voltage is less than 0.45 volt. DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt.
    DTC P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.
    DTC/HO2S Reference List
    • HO2S-11 = DTCs P1131, P1132 and P1130
    • HO2S-21 = DTCs P1151, P1152 and P1150
    Possible causes:
    Fuel system
    • Excessive fuel pressure.
    • Leaking fuel injector(s).
    • Leaking fuel pressure regulator.
    • Low fuel pressure or running out of fuel.
    • Contaminated fuel injector(s)
    • Vapor recovery system
    Induction system
    • Air leaks after the MAF.
    • Vacuum leaks (vacuum lines and gaskets).
    • Restricted air inlet.
    • PCV system.
    • Improperly seated engine oil dipstick.
    EGR System
    • Leaking gasket.
    • Stuck open EGR valve.
    • Leaking diaphragm.
    Base engine
    • Oil overfill.
    • Cam timing.
    • Cylinder compression.
    • Exhaust leaks before or near the HO2Ss.
  • Check intake air system for leaks, obstructions and damage.
  • Check air cleaner element, air cleaner housing for blockage.
  • Verify integrity of the PCV system.
  • Check for vacuum leaks.

Feb 12, 2011 | Ford Contour Cars & Trucks

1 Answer

2006 hundai elantra P2270 code. If this is an O2 sensor, which one?


Possible O2 sensors:

P2270 O2 Sensor Signal Stuck Lean Bank 1 Sensor 2
P2271 O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2272 O2 Sensor Signal Stuck Lean Bank 2 Sensor 2
P2273 O2 Sensor Signal Stuck Rich Bank 2 Sensor 2
P2274 O2 Sensor Signal Stuck Lean Bank 1 Sensor 3
P2275 O2 Sensor Signal Stuck Rich Bank 1 Sensor 3
P2276 O2 Sensor Signal Stuck Lean Bank 2 Sensor 3
P2277 O2 Sensor Signal Stuck Rich Bank 2 Sensor 3
P2278 O2 Sensor Signals Swapped Bank 1 Sensor 3 / Bank 2 Sensor 3
---
This is Bank 1 (closer to the dash panel) Sensor 2 (located after the catalytic converter).

---
Note: A malfunctioning front oxygen sensor may cause fuel trim codes to set.
  1. Several Diagnostic Trouble Codes use specific terminology to refer to sensor location. The illustration and key below explain the following terms:
  2. Engine BANK Bank 1 is closer to the dash panel, (also referred to as RH or right hand). Bank 2 is closer to the radiator, (also referred to as LH or left hand).
  3. UP Refers to Sensor 1 or "front sensor". It is located closer to the exhaust manifold and before the catalytic converter.
  4. DOWN Refers to Sensor 2 or "rear sensor." It is located after the catalytic converter.
  5. The following examples show how to interpret oxygen sensor terminology:
  6. B1/S1 = Bank 1/Sensor 1 = Dash panel side, BEFORE the catalyst or "upstream"
  7. B2/S2 = Bank 2/Sensor 2 = Radiator side, AFTER the catalyst or "downstream"

Aug 06, 2010 | Hyundai Elantra Cars & Trucks

2 Answers

Failed smog test because of fault code po174 : system too lean (bank 2) ford taurus 1998


Leak on the intake, bad EGR valve that's not closing. Perhaps a bad O2 sensor, but probably not. The O2 sensor is what detects a rich/lean condition. But when they fail they usually give their own error codes.

Feb 05, 2010 | 1998 Ford Taurus

1 Answer

Yes my truck is 1998 ford f 150 4.2 an i have code po174






DTC code p0174 means "System too lean (Bank 1)"

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exahust). On V6/V8/V10 engines



, Bank 2 is generally the side of the engine that doesn't have cylinder #1.

Jan 09, 2010 | 1999 Ford Windstar

1 Answer

96 ford explorer codes too lean bank 1 and 2


1. a vacuum leak. 2 low fuel presure. 3 bad airflow sensor.4 an exhaust leak before bank 1 or bank 2 o2 sensor 2

Oct 11, 2009 | 1996 Ford Explorer

4 Answers

Check Engine light is on my 1997 F150 with a small V-8. The tester returns codes P0171, P0172, P0174 and P0175. What does all this mean?


those codes are for lean engine condition look for vac leaks at the back of engine to the pcv valve could hear hissing noise with engine running also check egr valve to be stuck open also when was last fuel filter changed? hope this helps .

Sep 16, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...