Question about 2009 Honda Pilot

1 Answer

The object detection sensor won't shut off

The sensor that shows "approaching object" continues to beep while the vehicle is stopped. its shuts off during acceleration

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 42 Answers

?? Clean off the eye?

Posted on Apr 15, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to locate fuel shut off switch


There is no fuel shut off switch on Oldsmobile or any other GM vehicle . When fueling the vehicle did you stop when the pump kicked off ? or did you continue to fill to top ? Flooded the charcoal canister an engine ! Is the check engine light coming on !

Jan 16, 2016 | 1999 Oldsmobile Intrigue

2 Answers

Motion sensor


No, the rear sensing system won't signal if you are in any gear except reverse. The wiring for the module is connected so that it turns on when you put the car in reverse. (This assumes the sensors haven't failed. If they are dirty, they can sometimes signal when an object isn't there.) Some newer cars have blind spot monitors that indicate an object approaching from behind and to the side; these don't indicate an object directly behind the car.

I hope this helps.

Cindy Wells

Nov 10, 2013 | 2005 Ford Freestyle

1 Answer

86 Nissan 300zx stalling out when stopping. Won't start back-up for about 5 minutes


check fuel filter, maybe have some debris that sometimes clogs

Mar 10, 2013 | Cars & Trucks

1 Answer

2007 GMC Yukon Denali The rear parking sensors only beep once when placed in reverse and the gauge inside goes up through the yellow bars as the vehicle is approaching the object but still no warning...


"Dealer says everything checks out ok". Translation: The dealer made a superficial operational check without bothering to run the diagnostic routine that would have pinpointed the real problem.

Dec 30, 2017 | 2007 GMC Yukon Denali

1 Answer

My park assit is on and the sensor are not working for backing up can they have dirt in them


{: ) The PARK ASSIST OFF message will be displayed when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged. • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

The SERVICE PARK ASSIST message will be displayed when the object alarm module detects a malfunction in the parking assist system and the system is disabled. It could be one of your sensors is at fault or even the module.

May 18, 2011 | 2007 GMC Yukon Denali

1 Answer

I installed the parking sensors yeaterday and now they continue to beep after I put them in reverse. I did the test where you turn on the ignition but not start the car and then put the lever in reverse....


hello i would like to help but can you give me information on the sensor kit you installed. some systems to beep and some only beep when the sensors detect something. also if they work fine with out the engine running but then don't work properly when the engine is run this could be there is to muck voltage for the sensors, some sensor kits are saying they are 12v, this is correct 12 volts, but the charging system on most vehicles are 14 volts, so you may have to fit a regulator to the feed wires to the sensor. you would need a 12 volt regulator board. this will stop any power going over the 12 volts to the device.

Jun 30, 2017 | 2005 Nissan Pathfinder

1 Answer

Rear sensor creates constant beeping. How do I stop it from continuing?


Clean the rear sensors and check for water in the trunk. ( around the spare tire . The electronic control module is on the left side . Mine got wet and shut off the senors. I removed it dried it and cleaned it with alcohol and it now works . If it is water get the trunk latch adjusted to seal properly.
Alan

Apr 11, 2011 | 2003 Jaguar S-Type

2 Answers

My 2007 Yukon has a problem with the park assist sensors. When I go in reverse sometimes, the warning beep repeats quickly and the lights flash like crazy but nothing is behind the vehicle. Sometimes the...


Check the system for DTC'S - diagnostic trouble codes should be the first step in the diagnostic process . Then reading factory service repair manual how the system works , viewing wiring diagrams .
Object Detection Description and Operation
Ultrasonic Rear Park Assist Operation
The ultrasonic rear park assist system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located in the rear bumper. The object detection system will notify the driver when backing up at speeds less than 8 km/h (5 mph). The object detection system will use the rear parking assist (RPA) display and the radio speakers for notification.
When the ignition is ON and the vehicle is placed into reverse, the object detection system performs a bulb check. During the bulb check, the 3 indicators on the RPA will illuminate for approximately 2 seconds to indicate that the system is working. The object detection system performs a bulb check and operates when the following conditions are present:
• The ignition is ON.
• The vehicle is placed in REVERSE (R) for rear parking aid.
• The vehicle speed is less than 8 km/h (5 mph). At speeds greater than 8 km/h (5 mph), the object detection system is disabled. The red indicator flashes to warn the driver that the object detection system is disabled.
The object detection system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located on the rear bumper. When the system detects an object, one of the following will occur:
• If the object is less than 0.3 m (11 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators flash and the chime sounds continuously for 3 seconds.
• If the object is less than 0.3-0.5 m (11-20 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators are ON.
• If the object is 0.5-1.0 m (20-40 in) away from the vehicle, the amber outside, and the amber middle indicators are ON.
• If the object is 1-2.3 m (40-91 in) away from the vehicle, the amber outside indicator is ON with a single chime when the object is first detected.
Object detection system can detect objects 7.6 cm (3 in) wide and at least 25.4 cm (10 in) tall. It cannot detect objects above the level of the roof.
If the object detection system detects a malfunction, a diagnostic trouble code (DTC) will be stored and the object detection system will send a serial data communication message to the instrument panel (I/P) to SERVICE PARK ASSIST message on the driver information center (DIC). Then the chime will sound and the red indicator on the information telltale center will be lit continuously. The red LED in the rear display will be lit, notifying the driver that a malfunction exists. Message will clear once the driver acknowledges it.
Each object sensor is a three wire sensor that is both a transmitter and a receiver that comprises a signal circuit, a low reference circuit, and an 8-volt supply voltage circuit. The rear object control module supplies 8 volts to the object sensors via the object sensor supply voltage circuit and provides ground via the low reference circuit. The rear object control module triggers the sensors in a sequential loop and after each sensor transmits, the rear object control module uses the echo or signal return to calculate the distance and position of an object from the rear bumper. The rear object control module directly controls the RPA display.

Do you know what DTC'S are ?
DTC B0958 01: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Battery
DTC B0958 06: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Ground or Open
DTC B0958 08: Parking Aid Rear Sensor 1 Left Corner Circuit Signal Invalid
DTC B0958 21: Parking Aid Rear Sensor 1 Left Corner Circuit Incorrect Period
DTC B0959 01: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Battery
DTC B0959 06: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Ground or Open
DTC B0959 08: Parking Aid Rear Sensor 1 Left Middle Circuit Signal Invalid
DTC B0959 21: Parking Aid Rear Sensor 1 Left Middle Circuit Incorrect Period

DTC B0967 02: Parking Aid Switch Circuit Short to Ground
DTC B0968 00: Parking Aid Indicator Circuit


Your best bet , take it to a qualified repair shop.

Feb 04, 2018 | GMC Yukon Cars & Trucks

3 Answers

What does "service park assist system" mean on my 2008 jeep?


The park assist system detects objects 59 inches or less in back of your vehicle, to warn u so u don't strike the object. I'm guessing that since the service park assist system comes on in the ice and snow, the monitor is detecting something (ice and snow covering the sensor). If u clean off the snow and ice, the message should shut off.

Jan 13, 2009 | 2007 Jeep Commander Rocky Mountain

1 Answer

1993 Honda Prelude


door is ajar in switch clean latches with pb blaster close several times should quit beeping

Jul 01, 2008 | 1993 Honda Prelude

Not finding what you are looking for?
2009 Honda Pilot Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...