Question about 1983 Volkswagen Scirocco

1 Answer

HOW DO I PULOL THE MOROR IN MY SCIROCCO

IM HAVING TROUBLE PULLING THE MOTOR. DO I HAVE TO REMOVE THE TRANSMISSION FIRST

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 67 Answers

The group engine and gearbox,taken of under the car

Posted on May 02, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 1999 Ford Explorer sideview mirrors


REMOVE SIDE COVER MAYBE DOOR PANNEL CAUSE THE POWER WIRE WILL BE HELD ON THE IN SIDE SHOULD BE 3 10 MM BOLTS GOOD LUCK WITH MOROR. I THING IT IS ASSEMBLY

Feb 14, 2013 | 1999 Ford Explorer

1 Answer

How do u remove the passenger moror mount bracket on a 2002 chevy venture lt


Do you mean motor mount bracket? I would also assume that you mean the bracket that loops around the front of the engine on the right side of the vehicle - around the oil pan?
If this is what you mean, all I have to say is HAVE FUN! Those can be extremely hard to get off when you are in the shop with all the correct lifting equipment.

You must remove the air conditioning compressor from the front to get to those bolts and the only way to get the bolts on the other side is with an open-end wrench and a LOT of patience. The only thing harder than removing those bolts from between the engine and transmission housing is trying to get them started back in.

Apr 14, 2012 | 2002 Chevrolet Venture Passanger

1 Answer

I'm repairing the oil pan but I can not remove it, how do I remove the transmission


Before you remove the transmission and not knowing the condition of your oilpan, I might be able to save you some trouble.
If you have a few leaks in the metal of the oilpan, JB Weld can be used without replacing a pan. If you have a stripped drain hole, there are oversized plugs and rubber expansion plugs for that problem.

Sometimes you need to turn the crankshaft to clear the rods. And you can clear the frame and the oilpump with the oilpan by loosening the motor mounts and trans mounts and lifting the motor and reblocking the motor mounts.

But if you want to still pull the trans out, you will pull the driveshaft, the trans linkage and dipstick pipe. Then unbolt the starter, torque converter, and finally every bolt on the trans case to motor block. Earlier you loosened the trans mount bolts, now the frame crossbar should be unbolted and everything should drop.

Dec 26, 2009 | 1997 Ford Aerostar Extended

2 Answers

I cannot get my 1999 Silverado to go into 2wd. It is in 4dw hi. I've replaced the pushbutton control switch on the dash with a new one, and replaced the solenoid on the front diff with a used one. The...


Ckeck the acuator motor on the transfer case it may be burned out. With the key on (motor off) transmission in nutral try switching from 2 to 4 wheel drive and back you should hear the acuator moror run folowed by a click each time you activate the switch.

Oct 05, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

1992 Jeep Cherokee climate controls just stopped working


unplug the blower motor, try that, i have seen a direct short in the blower motor cause that. also check the blower moror resistor--again another fault---hope that was helpful

Aug 05, 2009 | 1992 Jeep Cherokee Briarwood

1 Answer

87-scirocco where is the backup lights swicth


The switch is located on the transmission... on top... look for two wires...

Apr 22, 2009 | 1987 Volkswagen Scirocco

1 Answer

Need assitance for vw repair


You are probably right, the clearance between the pistons and the valves is very tight on the 16 valve engines. one of the valves may have hit a piston., or even worse bent a rod or damaged the crank.
I would run a compression check, or leakdown check before pulling the head. I have a service manual for 90-93 Passats w/ 9A 16 valve engines. the manual says compression should be 145-189 psi. limit 109 psi w/ 44 psi max difference between cyclinders.

On these engines you also need to check that the timing on both cams is ok.

Apr 16, 2009 | 1984 Volkswagen Scirocco

1 Answer

Transmission fluid 1988 vw scirocco


Put it down the dipstick tube that you check the trans fluid with using a funnel. Don't put much in at a time before you check the level - remember to check the level with engine running, trans warmed up after driving 15 minutes and the car in park with parking brake on. Put the fluid in and see what it does for your shifting.

Jan 08, 2009 | 1988 Volkswagen Scirocco

1 Answer

Interment spark to plugs no start 85 vw scirocco


should run great go back to timing and check alignment of tdc to camshaft

Nov 15, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8759 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...