Question about 1983 Volkswagen Scirocco

1 Answer

How do i pull out the motor do i have to remove the transmission first

I'm trying to pull the motor and I don't have enough space with the transmission

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 67 Answers

Group under the car,complete,disassemble afyter,

Posted on May 02, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A 1999 MERCURY TRACER THE TRANSMISSION MOUNT BRACKET IS IN THE WAY TO GET THE TRANSMISSION PAN OFF ANY IDEAS??


sometimes its easier to use a engine lift and just loosen the motor mounts and ****** mount and lift the motor and trans just enough to remove the pan but makesure you dont lift to much as to hit the firewall or underside of the car.

Sep 20, 2012 | 1999 Mercury Tracer

2 Answers

I need steps of removing a transmission from 1981 chevy tow truck


  • Remove the TV cable or transmission throttle cable from the carburetor or throttle body. Remove the upper bolt holding the transmission dip stick but do not remove the tube. Disconnect the negative cable to the battery. Drain the transmission fluid by removing the transmission pan. Replace the pan after draining the fluid.
    Remove the shift linkage and the wires to the neutral safety switch. Remove the speedometer cable by unscrewing the cap at the point it enters the drive gear in the tailshaft. If it has an electronic speedometer, disconnect the electrical connector.

  • Install the engine support stand above the engine. Remove the CV joints. Remove all electrical connectors from the transmission. Remove the bolts in the torque converter. Place the floor jack under the transmission. Raise the transmission just enough to support it. Remove the transmission mounts. Lower the transmission enough to have access to remove all the transmission bolts. On a rear wheel drive vehicle, remove the bolts in the bottom of the transmission mount. Raise the transmission enough to remove the cross member.
    Once the bolts are out remove the cross member and then lower the transmission. Remove the dip stick tube from the transmission by lifting up. If it is hard to come out tap its mounting bracket with something and it will come up and out. Support the transmission securely on the jack. Using a flat head, separate the transmission from the engine. Lower the transmission.

    hope this helps

    but you can also just pull the motor and trans for better access ive also got an 85 chevy im about to do some work on ganna pull and rebuild the motor which is a first for me so if u know any one i could also get some tips from help would be awsome thank you

Nov 10, 2011 | Honda Cars & Trucks

1 Answer

I have a 1987 nissan pick up d-21 with the 3.5 DOHC engine and a 5 speed manual trans in this 4X4 I am pulling the engine out, do i have to pull the trans ? or can i oull just the engine? The oil pan seems...


I don't recall what those are like under there but things I have done to leave the transmission in are,
Pull the drive shafts and unbolt the transmission mount so it can be slid back but left in the truck.
Unbolt the mount (or leave it bolted if it will move enough) so the transmission still sits on it but jack the front of it up while lifting the motor so it can be pulled out of the trans enough to clear the input shaft.
Sometimes they take a little pull the motor forward and inch and then lift and inch then pull forward another inch and then lift another inch.....

Good luck on your swap. I was just doing the head on a 87 Nissan D21 with the Z24i and was looking for a later donar with ported injection for it instead of that TB injection also.

Sep 13, 2011 | 1987 Nissan Pickup

1 Answer

How do you replace the clutch on a 94 tercel


pull the cv axles, remove the transmission, remove the clutch assembly , reassemble, if you have never done this before I suggest you purchase the manual for that car , it has the step by step process,, which they don't allow me enough space here to fully answer that

Jul 26, 2011 | 1994 Toyota Tercel

1 Answer

We are repalcing a transmission on a suzuki forenza .How do you remove the axels


You will need to remove the lower control arm from the knuckle/hub carrier(at the balljoint) and also unbolt the hubnut. You should then be able to pull the hub assembly away from the vehicle to give you enough free space to remove the axle from the carrier. The other end of the axle pulls out of the transmission.

Oct 31, 2010 | 2005 Suzuki Forenza

1 Answer

I unbloted the starter but there not enough room to pull out the starter


YOU HAVE TO REMOVE SKID PLATE AND DRIVE SHAFT. THE EARLY MODEL YOU HAD TO RAISE THE ENGINE AND TRANSMISSION WITH A FLOOR JACK UNDER THE TRANSMISSION AND REMOVE THE TRANSMISSION CROSSMEMBER FOR ACCESS STARTER MOTOR BOLTS.ALSO REMOVE STARTER HEAT SHIELD.

Jul 08, 2010 | Chevrolet S 10 Cars & Trucks

2 Answers

Need to pull a siezed engine from a 99 avenger (can't turn it over to undo torque converter bolts) Can it be pulled without pulling the transaxle? (is there enough clearance to pull the engine with torque...


There isn't enough room to pull the engine without removing the converter. You can try to separate the engine and the trans far enough to get to the bolts with a wrench. Or remove the engine and transmission together and unbolt the two out of the car.

Jun 18, 2010 | 1997 Dodge Avenger

2 Answers

Can't pull out 97' Cadillac engine from the top


remove damper from the crankshaft, remove compressor, engine can be removed from the top

May 15, 2009 | 1997 Cadillac DeVille

1 Answer

96 Chevy S-10 starter problems


Just did this, take the long bolt out of the passenger side engine mount, loosen the two transmission mount bolts and jack the right side of oil pan slowly, when you do this there will be enough clearance between the bell housing and frame, be sure to use a jack stand to be safe.
Put the starter motor in the space with the selonoid up and wiggle forward into position then insert bolts and hook up connections. Let the motor down, put the motor mount bolt back in, tighten transmission mount.

Apr 16, 2009 | 1996 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...