Question about 2003 Mazda Mazda6

1 Answer

CD is stuck in player...will not load or eject another CD

Has anyone had this problem...and if thye had how did you fix it?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,854 Answers

Turn the radio off then disconnect the battery for 30 seconds. Reconnect the battery and turn on the radio, that my reset the radio for the Cd to be ejected. Good luck and hope this helps. MAKE SURE THE RADIO IS OFF BEFORE YOU DISCONNECT THE BATTERY. If the radio is left on you'll be prompted to enter a radio code.

Posted on Jun 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Loose female recepticle for fuel pump relay. Relay must be forced into a specific position. when I hit a bump the car stalls and thye relay hs to be repositioned.

don't do it. its to much work. just take the relay and use some pliers to twist the prongs don't bend but twist so they are on a 30 degree angle then push it in. this will make a good connection forever. a little dielectric grease will also help the connection

Nov 21, 2013 | 2005 Chevrolet Uplander LS

1 Answer

Easiest way to fix cracked heads on a 2004 Tahoe has white smoke coming out of exhaust

In most cases thye can't be fixed, they have to be replaced.

Oct 29, 2012 | Cars & Trucks

1 Answer

Fuel will not go to the injectors help??

check current to fuel injectors and also make sure the the correct fuel pressure is coming to fuel manifold. If you have only a few PSI of fuel to injectors then thye will not operate correctly but fuel will fill the line. You will need a fuel pressure gauge kit that has a hose and fitting attached. Try auto parts store for one.

Dec 02, 2011 | 1997 Oldsmobile Achieva

1 Answer

E 250 brakes get stuck? I recently had probelm with my front brakes since thye get stuck sometimes. I replaced teh calipers but the problem continue. How do i fixed the problem

did you grease the slide pins on caliper when putting them on ! sometimes the front brake hose collapses on inside, not letting fluid out of caliper to back it off from rotor. try replacing the brake caliper hoses first ! good-day !

Oct 27, 2011 | Cars & Trucks

1 Answer

My windshield wipers don't work ? the fuse is good checked that the other day, it seems like its thye switch that has a short or something, do i have to diagnose the steering colum and take that a-part...

Try turning the wiper switch on and pressing on the circiut board [ black plastic panel ] of the wiper motor. If it starts to work, the brushes may be worn and are part of the board [ very common on older vehicles ]. The board is easy to replace [ 3 screws ] and avialble at most autoparts stores or a GM dealer.

May 26, 2011 | 1988 Chevrolet S-10

1 Answer

New alternator not charging

check the 2 small wires on the positive post of the battery. thye corrode. Also check the wiring from the battery to the alternaotor

Dec 28, 2010 | 2000 Mercury Cougar

1 Answer

Clutch on ac compresser will not engage

check the a/c fused and see if geting any voltage at the a/c compressor wire connection , thye a/c switch must be on . if not the system may need gas

Aug 02, 2010 | 1998 Cadillac DeVille

1 Answer

How can I turn off the maintenance light on my 2006 Honda Pilot?

with the key in acsessory position press the gas peddal to the floor three times then turn thye key off and then start the car that should clear the light

Mar 02, 2009 | 2006 Honda Pilot

1 Answer

Power Seat

It was a simple fix. Tilt the seat all the way back. The front/back motor is the second from front. Take off the piece that holds the cable to the motor. Mine was just loose. I out it back in and it started working. I read you may have to shorten the black sheathing that houses the cable. This would be easy as well. Just remove thye metal piece and cut some of the black off and re-attatch the metal piece. Re-assemble and enjoy the fact you did not give the dealer 300 dollars.

Jul 03, 2008 | 1996 Volvo 960

Not finding what you are looking for?
2003 Mazda Mazda6 Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides