Question about 1993 Honda Civic 4 Door

1 Answer

Replace door handle honda civic

I have a replacement handle, but can't figure out how the rod that actually opens the door is attached to the new handle. The rod is threaded into a small cylinder that is attached to a hole in the new door handle mechanism. Is it a bushing or something that holds it in place? The hole in the new handle mechanism is not threaded.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 40,786 Answers

IT is possible that the manufacturer realised a fault existed in the current design and changed to a threadless part that requires a nut either side to position it on the rod . Try something in the area to see if it works Nuts that small can be obtained from an electronic shop such as JAYCAR ---Hobby shop --etc

Posted on Mar 22, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4793 Answers

SOURCE: Want to replace the drivers door lock cylinder on

it is a pushfit spring washer that holds the outer ring in position.if you prise it off you may have to replace it.

Posted on Mar 31, 2010

agent91
  • 2100 Answers

SOURCE: Remove the door panel on a 98 Honda Civic

You should have some little plugs in the plastic edge on the bottom that can be popped off, that will expose screws, there is maybe one screw behind the door handle, and maybe a couple in the door pull. Then once it is unscrewed, pop off the plastic retainers that hold it the rest of the panel and up it goes, past the lock button and off, except that it is still connected by wires, you should be able to see what's going on behind the handle without taking the wires loose, just lean it up against the door or the car. There is also a plastic wind barrier stuck on there with the stickiest stuff you ever saw, take off your watch. Hope this helps.

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 97 Honda Civic Lx & the back doors are


I had to put mine in the shop 3 times for this. Rear doors would only open from inside. Ad the drivers side door would not open either way. They had to replace a part in the door. I will find out what exactly was fixed and post tomorrow. I just got mine out of the shop today. They had it 13 of the last 20 days

Aug 25, 2013 | Cars & Trucks

1 Answer

1998 honda civic rear door handles work but lock won't unlock


THERE IS A CLIP ON THE INSIDE OF THE DOOR ON METAL ROD THAT GOES TO THE LOCK MAKE SURE ITS NOT DAMAGE OR FALLEN OF WHERE THE ROD GOES TO THE LOCK THERE ARE 2 ROD ONE OPENS THE DOOR THE OTHER ONE LOCKS THE DOOR

Sep 09, 2012 | 1998 Honda Civic

1 Answer

1998 honda crv door will not open from the inside but will on the outside


I am sorry to say that you did not read the question carefully: the door CAN be open from the OUTSIDE; i do have the same situation on my CR-V 1998; This has nothing to do with the latch itself: There is a connecting rod holder inside the dood which is probably broken (made of plastic) so when you open the door from inside,the rod connected to the handle goes away from the panel,and the course is too short; this plastic holding part must be replaced.

Apr 27, 2012 | 1998 Honda Civic

3 Answers

How do you replace an exterior door handle on a 2008 Yukon Denali


u can access thes handles by removing the door panel. u then unhook any cables and wires to the panel and then peel back the noise supressor film and then can u actually see the handles an bolts attaching the handle an a couple of linkage rods attach to it. kind of an easy job....good luck

May 10, 2011 | 2008 GMC Yukon

1 Answer

The door handle on the driver's side is broken...if you try to pull the handle the door does not open, you need to open it from the inside to get it open. How do we fix it?


1. You need to remove the door panel on the inside of the door first.
2. Make sure the window is all the way up.
3. Remove approximately 2 or 3 screws and the rod that is attached to the handle from within the inside of the door.
4. Replace with new handle attach screws and attach rod.
5. Put door panel back on and your done.

Oct 11, 2010 | 1990 Oldsmobile Silhouette

1 Answer

Honda Civic 2003. I need to separate (disassemble) the front door panel (plastic part in the inside side of the door) from the actual door so I can replace the lock cylindir. I have succeeded separating...


There might be hidden screws , usually at door handle , pluged with round plastic caps , or at door opening handle with small round cap.Look around and see what you can find .

Jun 08, 2010 | 2003 Honda Civic

1 Answer

How does the door linkage work i.e a diagram


There are plastic connectors that attach to the rod and attach to the latch. The rod usually hooks into the inside latch, the rod may be held to the door by some clips. Then the rod connects to the latch with a plastic retainer clip.

Mar 13, 2010 | 1993 Honda Civic 4 Door

1 Answer

I am trying to fix a door handle that will not open from outside


Turn the window handle to where you can see a small 1/2" slot rt at its base where it meets the panel.you'll notice a small brass v shaped clip,you'll need hooked pick or something simular to hook this clip and pull it out of its slot,this release's window crank handle. Once this is off the rest of panel is held on by plastic panel clips that pull loose by pulling panel outwards from door ,and also by a few various screws. once panel is off temp. slide window crank back on and crank window all the way up. You then should have clear view of outer door handle. Handle has two rods attached to it,one for lock assy., one for latch release.This is the one you'll be looking at.Most likely you will find rod has came loose due to broken retainer clip at handle,or casting on handle itself has broken off.If clip is broke you can buy new clip at dealer or at some autoparts outlets,replace and reattach rod(make sure rod locks into place).If handle casting is broke will need handle replaced.It is held in place by two 10mm bolts,two rods preeviously mentioned. If handle is body color matched will need color code(on door jam sticker)to order handle from dealer to match.Lock assy will need to be transfered to new handle,it is held in by two spring clips.You notice two holes one on each side of lock,you will need to push release clips inwards through each hole to release lock and slide it out.to install just push down into newhandlle until clips engage. Let me know if you run into problems. Good luck and if this was able to help you please leave me some positive feedback. Thanks and good luck, Joel

Oct 12, 2009 | Honda Civic Cars & Trucks

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

Not finding what you are looking for?
1993 Honda Civic 4 Door Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...