Question about Ford Fusion

Open Question

Ford fusion 58 diesel brake locked car wont start

Battery ok tested

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
txkjun
  • 409 Answers

SOURCE: 1992 Ford F350 Dually Diesel Truck Brake System problem.

Adjust your rear brake shoes. Then rebleed the system. Start at the master cylinder Bleed master first then the wheel furthest away from the master (right rear then left rear then right front then left front. Do that and your pedal should be good.

Posted on Dec 30, 2008

Ad
rockitman187
  • 2559 Answers

SOURCE: No radio volume (locked after changing battery of 06 Ford Fusion

Has to be unlocked by a dealer.

Posted on Jan 07, 2009

  • 93 Answers

SOURCE: Shut 05 Ford f350 diesel off wont start

dies the truck restart once it cools off? it is very common for th 6.0 to have high pressure oil issues on a hot soak. they will run till the cows come home but once shut off they can not build up enough pressure by cranking speed alone to start truck until it cools down and the seals become rigid enough to bridge the gaps they are sealing in the first please. if this is the case. it may be the STC fitting ojn the back of the high pressure oil pump (intake and turbos must be removed to check) or possibly the branch tube o rings have worn. the branch tubes are located under the valve covers and supply the fuel injectors the oil they need to perform their "power stroke"...

Posted on Jun 06, 2009

  • 184 Answers

SOURCE: ford fusion 1.4 tdci will not start unless the hand pump is used

HAVE YOU CHECKED THE FUEL LINES WHERE THE FUEL PRIMING PUMP IS CONNECTED FOR ANY CHAFFING THEY ARE COMMON FOR CHAFFING BESIDE THE FUEL FILTER WHICH WOULD EXPLAIN WHY FUEL IS RETURNING TO FUEL TANK.

Posted on Sep 11, 2009

  • 4 Answers

SOURCE: diesel ford will crank but wont start acts like

If you have the 6.0 ltr diesel, then check the bowl where the 2nd fuel filter is, see if there is fuel in the bowl, if not then either your fuel pump which is on the frame under the driver's side in the water seperator/ heater has gone bad, or your filters could be bad, or the fuse to the fuel pump or the pump shut off switch which is located on the side panel at your feet on the passengers side, there is a reset button, make sure it has not popped and press it down, hopefully this helps, I had the same prob.

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2014 ford fusion engine wont crank after wreck


Ford fusion won't start - YouTube

? 2:01
www.youtube.com/watch?v=H0BhHWT2cyY
Sep 16, 2014 - Uploaded by mlmunoz21
Ford fusion won't start ... Published on Sep 16, 2014 .... 2004-2008 F150 Died Out No Crank Theft Light ...

Ford Fusion won't start - YouTube

? 0:32
www.youtube.com/watch?v=lmH7R6Ebmyc
Jan 9, 2015 - Uploaded by Nicholas A.
Any ideas why it won't start? 2007 ford Fusion awd 6 cylinder. ... And P1260 2007 Ford Fusion - Theft ...

Nov 02, 2015 | 2014 Ford Fusion

1 Answer

My 2006 Ford fusion does not release the key from the ignition when it's in park???


You have a problem with THE SHIFT INTERLOCK SYSTEM !


The floor shifter assembly:




  • locks the transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.

  • requires the transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.




PINPOINT TEST A: THE SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY







A1 TEST THE BRAKE LIGHTS









  • Apply the brake pedal and view the brake lights.

  • Do the brake lights illuminate?




Yes

GO to A2 .



No

REFER to Section 417-01 .




A2 TEST SHIFT INTERLOCK ACTUATOR POWER CIRCUIT









  • Disconnect: Floor Shifter Harness Connector C3245.

  • Key in ON position.

  • Measure the voltage between floor shifter harness connector C3245-1, vehicle harness side and ground, while applying the brake pedal.

    Is the voltage greater than 10 volts?
A3 TEST SHIFT INTERLOCK ACTUATOR GROUND CIRCUIT



  • Key in OFF position.

  • Measure the resistance between floor shifter harness connector C3245-4, vehicle harness side and ground.

    Is the resistance less than 5 ohms?

Yes

INSTALL a new selector lever. Refer to Selector Lever in this section.

No

REPAIR the circuit. TEST the system for normal operation.

May 25, 2015 | 2006 Ford Fusion

1 Answer

We own a 2014 ford edge..will not unlock with fob, key or driver side code.


See page 58 for key operation
No discussion on dead battery enter.


http://www.fordservicecontent.com/Ford_Content/Catalog/owner_information/2014-Edge-U387-Owner's-Manual-First-Print_om_en-us_11_2013.pdf

OK different model but at least one other ford car owner is confirming that car will not open with key dead battery.

I suggest using a little effort on the key. Do not break the key!!!.
In the following forum the owner indicated a different feel as if the mechanical lock was maybe interacting with the anti theft system!!

I O course make sure you have the right key!!! whi knows keys can get mixed up.

Dead Battery Door Locks Inoperative Ford Fusion Hybrid

If the battery is dead I might consider searcing under the car for the starter motor battery connection and charging the battery. Least risk.

Opening hood with jimmy tool is possible. I would find a similar Edge and practice with the hood jimmy tool with the hood open before I would tear up the finish trying to open the hood

With the VIN number in hand I might go back to dealer and confirm key!!!

Good Luck

Feb 28, 2015 | 2014 Ford Edge

1 Answer

My ford fusion will not start,it gives me a message saying brake failure,but then will start after several try's any ideas?


Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.


To confirm the problem, the basic troubleshooting is required.


Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.

Thanks.

Feb 13, 2012 | 2006 Ford Fusion

3 Answers

How to overide limp mode in 2006 ford fusion


put the key in the ignition, and turn it so the lights and everything come on, do not start the engine, then pump the brakes 3 times, turn it off, and then start the engine. This worked for my 2008 for fusion. (if the brakes don't work, try the gas 3 times make sure the engine is off and the car is in park)
Best of luck!

Mar 01, 2011 | 2006 Ford Fusion

1 Answer

My Fusion wont start, I have had the battery checked and it is ok. When I turn the key only the oil lamp and safety lock light comes on and it keeps on going click, click, click. If the I jump start the...


First make sure your battery terminals are clean and tight. If this doesn't fix it, the problem may be a short in your system that is draining the battery. This case will require troubleshooting.

Please see my tip at http://www.fixya.com/cars/r5925550-dead_battery_troubleshooting . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Dec 11, 2010 | 2004 Ford Fusion

1 Answer

Engine light after dead car


try cleaning the battery terminals first and see what happens

Jun 04, 2010 | 2006 Ford Fusion

1 Answer

Wiper problem-93 Ford Ranger XLT,2 wheel drive,3.0 v-6.auto. Only have high speed,no more intermitent,no longer returns to start position-HELP


probably the motor but chaeck this first G3 CHECK CIRCUIT 58 FOR BATTERY VOLTAGE
  • Unplug wire harness connector.
  • Set wiper switch on low.
  • Check Circuit 58 for battery voltage key on.

    k17829a.gif

arrow.gifVoltage OK
CHECK for malfunctioning wiper motor. Perform low speed current draw test. SERVICE as required.
arrow.gifVoltage not OK
CHECK for:
  • Open connector.
  • Malfunctioning switch.
  • Malfunctioning governor.
  • Open wire Circuit 58 (W).

Jun 02, 2010 | 1993 Ford Ranger SuperCab

2 Answers

How do you press the brake caliper piston back on 2008


First, take a look at the piston, if it's flat or cup shaped, put an old pad at the piston and use channel locks to squeeze it back in, opening the tool wide to get it to catch the back of the caliper.
If....the piston has what looks like an "X" or cut outs, this is for a tool that spins the piston in with a special tool. (Subaru's and some other cars use this)
After you are all done and pump up the brakes, re-check the brake fluid level.

Dec 06, 2009 | 2008 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...