Question about 2010 Opel Insignia 1.6

Open Question

I want to exchange my insignia fog lamp cover

I need to remove the existing cover and replace it as it has been damaged

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the fog housing on a 2005 Mitsubishi Eclipse Spyder?? Does the whole front need to come off?


No. You can get to the fog lamps by removing the plastic under-covers from the bottom of the bumper facia. They are held in place with a bunch of plastic clips. Once the covers are removed, you will see the back side of the fog lamp assemblies where you can access the four mounting screws.

Apr 14, 2012 | 2005 Mitsubishi Eclipse Spyder

1 Answer

How to install a grill for a 2001 volkswagon beetle


TO REMOVE GRILLE FROM BEHIND THE BUMPER COVER RELEASE PLASTIC CLIPS AND DETACH THE GRILLE. IF YOU HAVE FOG LIGHTS DISCONNECT THE ELECTRICAL CONNECTORS FROM THE FOG LIGHTS AND REMOVE THE FOG LAMP MOUNTING SCREWS BEFORE DETACHING THE GRILLE.WHEN YOU INSTALL GRILLE PLACE GRILLE IN POSITION AND SEAT THE CLIPS INTO HOLES IN THE BUMPER COVER. IF YOU HAVE FOG LAMPS INSTALL GRILLE IN POSITION THE INSTALL FOG LAMPS MOUNTING SCREWS BACK IN PLACE TO HOLD GRILLE IN POSITION.

Sep 25, 2011 | Volkswagen New Beetle Cars & Trucks

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

The fog lights stay on after the ignition is turned off killing the battery


Your fog lamp relay is stuck open you need to locate it and replace it.Usually located under the hood in engine compartment in the fuse relay cluster.Open the cover and on the diagram detailed and numbered you will see fog lamp relay remove and replace this relay is most likely a dealer item.

Dec 28, 2010 | 2000 Mercedes-Benz SLK

1 Answer

NEED TO REMOVE EXISTING FOG LAMP HOUSING FOR REPLACEMENT


Hi, the fog lamp is held on , by 2 bolts at the back side of the bumper, on top of the fog lamp bracket. You would have to go underneath the bumper, and remove the two bolts, with a 10mm wrench. They are a bit tricky to get to, but it is easily done. Good luck...Coop

Sep 26, 2010 | 2002 GMC Yukon XL

1 Answer

How to take off existing fog lights on a 2003 escalade and install new fog light assembly


The fog lamp assemblies can be removed by getting underneath the front bumper and on top of the fog lamp assemblies you will find the metal mounting bracket. The bracket attaches to the vehicle with 3 small bolts that are 8-10mm (i forgot exactly) that bolt down through the bracket into the front bumper cover above the actual lens itself and can be accessed with a box wrench. I replaced both assemblies in mine in under 1/2 and hour!

Jun 24, 2010 | Cars & Trucks

1 Answer

How do I replace the Drivers side fog lamp (not just bulb) on my 2002 Audi A4 18T?


First remove the driver's side fog lamp plastic cover out from front bumper. After that you will find torx socket head panel screws from fog lamp. See picture below:

de0b0fe.png

Feb 06, 2010 | 2002 Audi A4

1 Answer

Fog lamp replacement on 2008 elantra


1. Disconnect the negative (-) battery terminal. 2. Remove the front side cover screw. 3. Remove the front fog lamp assembly connector (A).

38eda8f.gif 4. Remove the front fog lamp bulb (A).

20279ba.gif

Jun 20, 2009 | 2008 Hyundai Elantra

1 Answer

Need help replacing fog lamp in 2001 bmw 330i


Hi, the fog lamp should have a cover surounding it. this will just pull off then you will see a 8mm screw bolt, remove this and the fog lamp should then be able to be removed.

Mar 14, 2009 | 2001 BMW 330

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
2010 Opel Insignia 1.6 Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Brad Brown

Level 3 Expert

15451 Answers

george parkes

Level 3 Expert

975 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...