Question about 1998 Citroen Saxo 1.1

Open Question

Boot replace steering rack

Fitting boot

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vt commodore rack boots


Vt commodore steering Rack boots always rip and tear,the racks always tend to leak from the internal seals.
So if this the case with yours I would recommend you just get a reconditioned steering rack and fit it but once the rack is replaced you will also need to do a wheel alignment.
steps to change rack .
1.raise vehicle on hoist
2.remove front wheels
3.remove tie rod end split pins
4.undo tie rod end nuts and inner nuts on rack ends
5.release tie rod end from hub.
6.centralise steering wheel and remove keys from ignition
7.count the number of turns on each side that tie rod come off and write down .
8.undo the 2 metal pipes that go into the rack feed and return lines and make sure u have container under the vehicle to collect old fluid.
9.undo the 13mm nut and bolt that mounts the rack to the steering colum shaft.
10.undo the 2 *19mm bolts and nuts that mount the rack to the crossmember.
11.gentle wiggle the rack and it will come away.
12.follow these steps in reverse when fitting new rack.,make sure you replace the oring seals .
13.you will need to get a wheel alignment done..

Feb 12, 2014 | Cars & Trucks

1 Answer

My steering wheel is upside down.


things like that usually are not covered after fitting the rack take it for allignment

Apr 13, 2017 | 2007 Nissan Murano S

1 Answer

Is it possible for power steering fluid to get into the engine and mix with the oil? I am loosing fluid and there are no visible leaks, the engine oil and filter was recently changed and now has turne


No, the power steering is entirely a separate and sealed system, wholly external to the engine. The power steering pump pushes the fluid through a high pressure hose into the rack and pinion-the steering gear mounted below and behind the engine-and holds pressure within the rack that enables power assisted steering. At the same end where the power steering fluid hose enters the gear will be a fitting for a return line back to the fluid reservoir. These two hoses are usually routed close together at least part of the way, some may even be held together with brackets. Leaks could develop at the pump, the fluid reservoir, or the two hoses to and from the rack and pinion, or the seals inside the rack and pinion may have failed. You should be able to find the leak-it will only leak to the outside-to check the rack and pinion for leaks, right where your tie rods come out of the gear and go to the wheels for steering, will be a small rubber boot encasing the tie rod and the end of the rack assembly-on both ends is a boot and a tie rod-peel back the rubber boot from the gear ass\'y, it should be dry. If a lot of fluid, the seals in the rack and pinion are gone. It will have to be replaced.
Hopefully you will find a leaking hose or fractured reservoir, but keep looking, air flow may be blowing the leaking fluid back and under the car. Good luck, hope it\'s not the rack and pinion.

Jan 24, 2013 | Honda Cars & Trucks

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

Rack and pinion? have play in wheel no sign of leaks new power steering pump installed


Hi Gunny, If your vehicle is fitted with rack and pinion steering also check the rack ends for play. The rack ends are the rods which the tie rod ends screw onto. The other end fits onto the rack of the rack and pinion. To work on those you will need to remove the rubber boots and loosen the locking washer, they can then be loosened with a wrench. If they are worn the play will be evident in the steering. When replacing them also replace the rubber boots. If the boots are worn and road grime and dust enters, you will see leakage from the rack and pinion in the near future. I always thought the Dakota was fitted with a steering box? Regards John

Jun 24, 2012 | 1990 Dodge Dakota

1 Answer

My power steering fluids leaks daily - what needs to be done.


it depends where it is leaking from,if is a hose fitting it might just need tightening up,if it is from the power steering pump it is most likely the front seal behind the pulley & it will have to be replaced, or replace the whole pump, if it is the steering rack it could be the the pinion seal ( where the steering column connects ) at the ends of the rack where the tie rod connects (inside the rubber boots) all these seals can be replaced ,but sometimes it is better to fit reconditioned units, depending how many kilometeres/miles the vehicle has done.....hope this helps....cheers

Jul 04, 2010 | 2002 Kia Rio

2 Answers

Steering gear boot seepage.


the sterring rack (this is the long rack) must be replaced to correct this leak, the internal seal bore is most likely scored.

May 27, 2010 | 2006 Chrysler Town & Country

1 Answer

How do u replace the power sterring hose in a 2000 oldsmobile intrigue


You need a 16mm flare nut wrench - they sell them at Autozone. Buy two. Usually it is the high side that leaks - remove the fitting at the pump and at the rack. To get to the fitting at the pump you might want to fabricate your own wrench with a torch:

e18efcc.jpg
To get to the fitting at the rack you will want to remove the sway bar and drop the rear two bolts on the engine/ drivetrain cradle (you don't have to disconnect the steering shaft like I did - I was replacing the rack):

1b5e8c1.jpg
Check out the pix at http://99intrigue.shutterfly.com/steering for help, but like I say, those are about replacing the rack. Route the hose under the right tie rod on the factory clip.

Mar 08, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Loss of power steering fluid.but no signs of leakage


it will be filling up your boots from the steering rack.undo clamp on rubber boot on steering rack pull boot back ps fluid will run out.replace steering rack

Jul 16, 2008 | Mazda MAZDA6 Cars & Trucks

Not finding what you are looking for?
1998 Citroen Saxo 1.1 Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...