Question about 1994 Chevrolet S-10

1 Answer

4 wheel drive will not engage (1995 S10 Blazer)

When I first turn on the ingnition the 3-lights (4wheel high and low) on the 4 wheel switch panel turn on then go out after 5 seconds. Seems normal! I know the switches are working and the lights.

When I ty to put it in 4 wheel (high or low) no light indicator and the tansfer case shaft to the front wheel diff does not turn (drive the diff). Tells me the vehicle is not in 4 wheel. no indicatot light for low 4 wheel is not working as well no gear change. Could this be a vacume line on the trany?
4 wheel worked fine this winter....i needed most recently on a sandy beach.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

I had this same problem a few years ago. In my case I didn't use the 4 Wheel Drive very often and the tranfer would hang in 2 Wheel. I fixed mine by tapping on the transfer case with a hammer while my wife switched back and forth from 2 Wheel to 4 Wheel.

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my name is Larry I have a 1998 Pontiac sunfire & my problem that I have is I have low beam. But no high beam.


It's probably the switch , but testing to know for sure is alwasy a good idea .

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect a fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?

Daytime Running Lights (DRL) System Check
Step
Action
Normal Result(s)
Abnormal Result(s)*
1
Turn the headlamp switch to the HEAD position.
Turn the headlamp dimmer switch to the LOW position.
The low beam headlamps are ON.
The high beam headlamps are OFF.
Headlamps Inoperative - Low Beams
2
Turn the headlamp switch to the HIGH position.
The high beam headlamps are ON.
The high beam indicator is ON.
The low beam headlamps are OFF.
Headlamps Inoperative - High Beams
3
Turn the headlamp switch OFF.
Turn the ignition to ON.
Disengage the parking brake.
The high beam headlamps come ON at a reduced intensity in approximately 30 seconds.
Daytime Running Lamps (DRL) Inoperative, Headlamp Switch Operates Normally
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

Jan 13, 2017 | 1998 Pontiac Sunfire

1 Answer

96 explorer disengages 4wh low but does not engage 2wheel


Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

Mar 31, 2014 | 1996 Ford Explorer

1 Answer

2002ford explorer sport, the 4 wheel drive high or low


The transfer case may be hanging up, have you ever had it serviced with new fluid? If not do so and drive it for a few miles and try again, if that doesn't fix the issue you will need a shop to inspect the transfer case actuator motor and position contacts.

Nov 06, 2012 | Cars & Trucks

1 Answer

96 gmc 4wheel drive not engaging


There are many vehicles which notice same issue with 4wd not engaging in low or high mode.I suggest you few help links related to these issue,with there troubleshooting details and solutions.
Car will not go into 4WD high or 4WD low? http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html

------------
No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

--------
4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

---------
4WD light is flashing and beeping? NO 4WD high?

http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html

-----------
2002 Jeep Wrangler: 4WD Idiot Light is ON?

http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html

-----------

Traction control switch will not engage on 4WD High or Low
http://whoisbyme.blogspot.com/2012/10/traction-control-switch-will-not-engage.html

--------------
Service 4wd warning light on Dash? http://howtobyme.blogspot.com/2011/11/service-4wd-warning-light-on-dash.html

-----------
Car automatically switches to 4wd low?

--------
These are the help links related to your issue.Going through these help links,will guide you to troubleshoot and solve the issue noticed on your car.
Keep updated for more help.
Thanks.

Oct 17, 2012 | Chevrolet Cars & Trucks

1 Answer

How do i turn off my 4 wheel drive in my 2003 ford exployer


to turn off your 4wheel drive you push the auto button. no light will come on and your vehicle will be ready to drive normal. only use low when stuck or steep incline..and high in snowy weather but never on dry roads

Jan 08, 2012 | 2003 Ford Explorer

1 Answer

Will not go in 4 low 4x4 lights start blinking after trying . reset light by unhooking battery . then goes in 4 high normelly but not 4 low. i thlnk auto 4 is working 4 liter SOHC 1998


Normally 4 wheel drive HIGH is engaged on the fly or as you are moving more than 10 km per hour or 10 miles per hour but 4 wheel drive LOW is engaged at around 3 to 5 mph. no more or you could ruin the transfer case. Try going from 2 high to 4 high by switching back and forth and then try 2 high to 4 low when idling along. What usually happens is the mechanics under the car freeze up or rust up and you have to switch back and forth to free it up.

Nov 01, 2010 | 1998 Ford Explorer

2 Answers

When i turn the dial to 4wheel low the light


4 wheel low engages only when u shift trans into neutral or park never when moving it can cause transfer case damage.

Jul 16, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Stuck in four wheel low


start vehicle, put transmission into nuetral, rotate dial from 4 low to 2 or 4 high. must be in nuetral to change.

Feb 16, 2009 | 2007 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
1994 Chevrolet S-10 Logo

602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...