Question about 2006 Chevrolet Impala

Open Question

Replace RCDLR impala

Replace RLCDR

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for location of the keyless remote control module on a 2010 Chevrolet Avalanche LT


Remote Control Door Lock Receiver (RCDLR)
The remote control door lock receiver (RCDLR) is a multifunction module that operates both the keyless entry system as well as the tire pressure monitoring (TPM) system. When an RF message is received from a keyless entry transmitter, the RCDLR interprets this signal and will request via serial data that the body control module (BCM) perform the specific function, i.e. door lock, door unlock, or vehicle locate. The RCDLR also sends messages out to the 2 Way Advanced Remote Start transmitter.

Remote Control Door Lock Receiver (RCDLR) (AP3 or AP8, without E52)
Top rear of the passenger compartment above the rear window


Remote Control Door Lock Receiver (RCDLR) (AP3 or AP8, with E52)
Left rear of the vehicle behind the D-pillar trim panel

Body Control Module (BCM)
On the lower left side of the I/P to the left of the steering column


Good luck !

Jun 05, 2017 | Chevrolet Avalanche Cars & Trucks

1 Answer

How many wire harness clips connect to rcdlr module on 2007 impala besides the antenna


2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry
Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html
May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...


Dec 01, 2015 | 2007 Chevrolet Impala

1 Answer

2009 Buick Lacrosse automatic door locks, interior button and fob not working


Have you had it checked to see if DTC'S - diagnostic trouble codes stored in the BCM - body control module ? That's the first thing you should have done . Dealer or other independent reair shop that has a factory or professional type scan tool . Auto part stores can't pull these codes .
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
• The remote control door lock receiver (RCDLR)--When you press a button on the transmitter, the transmitter sends a signal to the RCDLR. The RCDLR receives the signal and sends a serial data message requesting the appropriate function from the BCM.
• Keyless Entry Antenna which is a coaxial cable that runs from the RCDLR to the back glass. It attaches with a 9 volt battery style connection to a grid on the back glass, this style antenna is used to increase range and performance for Keyless Entry and Remote Vehicle Start systems .

Jun 10, 2017 | 2009 Buick LaCrosse CXL

1 Answer

Can I turn the tire light off without having max air in my tires on my chev 2008 2500 silverado


no i dont belive so, you wolud probably have to replace the rcdlr to change the pressure settings but even that might not work

Jan 17, 2013 | 2008 Chevrolet Tahoe

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

1 Answer

The battery goes dead in my 2006 cady xlr after not driving it for 2 to 3 weeks, is this normal?


There Are 2 Software Updates That You Can Get From The Dealer (If Not Already Installed), One Is An Update For The ECM, The Other Is An Update For The RCDLR.
TSB07-06-03-001B (RCDLR)
The Other For The ECM Is An Unpublished Document
You Will Generally Be Looking At Paying 1H For Programming 2 Modules.
After This Have The Battery Properly Charged & Load Tested.

Oct 21, 2010 | 2006 Cadillac XLR

1 Answer

Key fob no longer works replaced battery and reprgrammed keyfob do i need another fey fob ir is it something within the car itself that need to be checked?


i would check the key fob first. the place where the battery goes take it out and check the silver connector the solder usually lets go in the fob itself and will not work. if the fob is ok the rcdlr will have to be replaced and your fobs will have to be re-programmed. rcdlr (remote control door lock receiver)

Feb 10, 2010 | 2000 Chevrolet Tahoe

1 Answer

2006 Impala TPMS regularly reads tire pressures wrong, sometimes says zero and other times it reads 35 psi. Two sensore act up more than the other two.


The remote control door lock receiver (rcdlr) antenna and receiver are the most likely cause of your problem. If you remove the A pillar molding on the drivers side you should see the antenna attached with a push pin against the paint. You could try attaching the antenna ground to the pillar by cleaning the paint off and using a real screw to attach the ground.

The other fix is having the rcdlr, antenna, and transmitters replaced which will cost you some money. This bulletin number will help if the dealership will print it for you. 07-08-52-001C

Nov 28, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

Replaced battery in remote even though old battery still had 3 volts,tried to initialze per instructions and still won't unlock door.get no chime when programming, just run out of time.2001 chevy impala


• Resynchronization may be necessary due to the security method used by the remote keyless entry system. Resynchronization may be necessary due to the security method used by the remote keyless entry system.
The transmitter does not send the same signal twice to the remote control door lock receiver (RCDLR). • The RCDLR will not respond to a signal that has been sent previously. This prevents anyone from recording and playing back the signal from the transmitter. • Resynchronization may be necessary under the following conditions: - The battery in the transmitter is very weak. - The battery in the transmitter was replaced. - The battery in the vehicle has been in a low or no charge condition for an extended period of time. • In order to resynchronize the transmitter with the RCDLR, perform the following steps: 1. Stand within 1.5 m (5 ft) from the vehicle. 2. Simultaneously press and hold the LOCK and UNLOCK buttons on the transmitter for 7 seconds

Jun 25, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

RKE not working


There si a service bulletin that has us replce the module, remotes, antenna, and reprogram. If the car has, say up to 40k miles or so, the dealer should take care of this under warranty, since this is a common problem, and there is a bulletin for it. It has nothing to do with the anti-theft module as a post above states. The module is called the " Remote Control Door Lock Receiver" (RCDLR)-
Tech JK

---------------------------

Dec 17, 2008 | 2007 Chevrolet Impala LS Sedan New Cars

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...